Bedienungsanleitung Siemens gigaset a155 (Seite 5 von 14) (Englisch)

298552

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

Gigaset A155 / GBR / A31008-M1717-L101-2-7619 / Ohio_AM_GBR.fm / 12.09.2005

The polarity is indicated in/on the battery compart-

ment.

Closing the battery cover

◆ Position the cover pointing slightly downwards

and push it up until it clicks into position.

Opening the battery cover

Press below the upper curve on the battery cover

and slide down.

Step 3: Charging the batteries

To charge the batteries, place the handset in

the base/charging cradle and leave for approx. 12-

15 hours. The batteries are now fully charged. The

battery charging status is correctly displayed only

after uninterrupted charging/discharging. There-

fore you should not interrupt the charging process.

Charging is controlled electronically to prevent the

batteries from overcharging. The batteries heat up

during charging. This is normal and not dangerous.

After a time the charge capacity will decrease for

technical reasons.

The charge status of the batteries appears at the

top right of the display:

The handset is already registered with the base sta-

tion. You must set the date and time to ensure that

the times of calls are logged correctly (page 7).

Your telephone is now ready to use.

Activating/deactivating the handset

Press and hold the end call key a.

If you place a deactivated handset in the base sta-

tion/charging cradle, it will automatically activate.

Activating/deactivating the keypad lock

You can "lock" the keys on the handset to protect

the keypad against inadvertent activation.

To activate: press and hold the hash key

The display shows the icon

Ø.

To deactivate: press and hold the hash key

The keypad lock deactivates automatically when

you receive a call and activates again after the call.

When the keypad lock is active you cannot even

call emergency numbers!

Making calls

Making external calls/Ending a call

External calls are calls using the public telephone

network.

(Enter the number) ¢c.

The number is dialed. (Or you can first press and

hold

c[dial tone] and then enter the number.)

During the call you can adjust the earpiece volume

as follows:

j ¢ H/SET VOL ¢ OK

Select the volume with x and w and confirm

with

OK.

Ending the call/canceling dialing:

Press the end call key

Answering a call

Your handset rings and you wish to take the call:

Press the talk key

If "Auto Answer" is active (page 8) just lift the

handset out of its base/charging cradle.

Calling Line Identification

When you receive a call, the caller's number will be

displayed on your handset; the caller's name will

be displayed if it is stored in the directory or if CNIP

has been requested.

Requirements:

1 You have asked your network provider for the

caller's number (CLIP) or name (CNIP) to be dis-

played on your handset screen.

2 The caller has asked the network provider for

his number to be identified (CLI).

◆ Never use non-Siemens chargers as

these could damage the batteries.

◆ Only place the handset in the base/

charging cradle that is intended for it.

‰ batteries flat

Š batteries 1/3 charged

‹ batteries 2/3 charged

Œ batteries fully charged

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens gigaset a155 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens gigaset a155

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info