Bedienungsanleitung Siemens gigaset al145 (Seite 9 von 12) (Englisch)

301189

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

L1a / IM-NORD En / A31008-M2001-R201-1-9W19 / AL140_IM-NORD_EN.fm / 09.09.2008

Care

Wipe the base station, charging cradle and handset

with a damp cloth (do not use solvent) or an anti-

static cloth.

Never

use a dry cloth. This can cause static.

Contact with liquid

If the handset has come into contact with liquid:

1. Switc

h off the handset and remove the bat-

tery pack immediately.

2. Allow the liquid to drain from the handset.

3. Pat all parts dry, then place the handset with

he battery compartment open and the keypad

facing down in a dry, warm place for at least

72 hours (no

t in a microwave, oven etc.).

4. Do not switch on the handset again until it is

mpletely dry.

When it has fully dried out, you will normally be

able to use it again.

Questions and answers

If you have any questions about using your phone,

visit us at

www.gigaset.com/customercare at any

time. The table below contains a list of common

oblems and possible solutions.

Authorisation

This device is intended for analogue phone lines in

your network.

Country-specific requirements have been taken

to consideration.

We, Gigaset Communications GmbH, declare that

is device meets the essential requirements and

other relevant regulations laid down in Directive

1999/5/EC.

A copy of the 1999/5/EC Declaration of Conformity

is a

vailable at this Internet address:

www.gigaset.com/docs.

Problem Cause Solution

Nothing

appears in

the display.

The handset is not

turned on.

Battery pack is

at.

Press the end call key

a for approx. 5 sec-

onds or p

lace the

handset in the base

station.

Charge/replace the

batt

ery pack (page 3).

No reaction

to key press.

The keypad lock is

tivated.

Press the hash key

for approx. 2 sec-

onds (page 1).

No wireless

nnection to

the base sta-

tion, Ba

flashes in

the display.

The handset is

outsid

e the range

of the base sta-

tion.

The handset is not

egistered.

The base station is

ot turned on.

Cords not routed

corr

ectly.

Move the handset

closer t

o the base

station.

(page 3).

Check the power con-

nector at the base sta-

tion (page 2).

Check cord routing

(page 2).

You cannot

ear a ringer/

dialling tone

from the fixed

network.

The phone cord

sup

plied has not

been used or has

been replaced by

a new cord with

the wrong jack

connections.

Please always use the

one cord supplied

or ensure that the jack

connections are cor-

rect when purchasing

om a retailer

(page 2).

Error tone

sounds after

system PIN

prompt.

PIN forgotten.

You have entered

the w

rong system

PIN.

Reset the system PIN

to the default 0000.

To do this, unplug the

mains unit from the

mains socket

£Press and hold the

paging key

£Plug the mains

adapter in again

£Hold the paging

key down for at least

another 2 seconds

and then release.

The reset procedure is

now

carried out.

The handsets are de-

registered. The calls

list is

cleared.

Problem Cause Solution

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens gigaset al145 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens gigaset al145

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info