300747
61
Zoom out
Zoom in
Vorherige Seite
1/80
Nächste Seite
59
Customer Service & Assistance
Gigaset E490/E495 / GBR / A31008-M2105-L101-2-7619 / appendix.fm / 15.05.2013
Version 4, 16.09.2005
Questions and answers
If you have any questions about the use
of your phone, you can contact us 24/7
at www.gigaset.com/service
. The table
below contains a list of common problems
and possible solutions.
E495 Gigaset only:
The display is blank.
1. The handset is not switched on.
¥ Press and hold the end call key a.
2. The batteries are flat.
¥ Charge or replace the batteries
(
¢page 10).
"Base x" flashes on the display.
1. The handset is outside the range of the base
station.
¥ Move the handset closer to the base sta-
tion.
The base station's range is reduced because
eco mode is activated.
¥ Deactivate eco mode (¢ page 45) or
reduce the distance between the handset
and the base station.
2. The base station is not turned on.
¥ Check the base station's mains adapter
(
¢page 8).
"Please register" flashes in the display.
Handset has not been registered with the base
station or has been deregistered.
¥ Register the handset (¢page 46).
Handset does not ring.
1. The ringer is deactivated.
¥ Activate the ringer (¢page 53).
2. Call divert set to All Calls.
¥ Deactivate call divert (¢ page 25).
You cannot hear a ringer/dialling tone from the
fixed line network.
The phone cord supplied has not been used or
has been replaced by a new cord with the wrong
pin connections.
¥ Please always use the phone cord supplied or
ensure that the pin connections are correct
when purchasing from a retailer (
¢page 8).
Error tone sounds after system PIN prompt
You have entered the wrong system PIN.
¥ Reset the system PIN to 0000 (¢page 55).
Forgotten the system PIN.
¥ Reset the system PIN to 0000 (¢page 55).
Call charges are not displayed.
1. Your network provider does not support this
feature.
2. There are no metering pulses.
¥ Ask your network provider to transmit the
metering pulses.
The other party cannot hear you.
You have pressed the
u (INT) key. The handset
is "muted".
¥ Activate the microphone again (¢page 23).
The number of the caller is not displayed
despite CLIP.
Calling Line Identification is not enabled.
¥ The caller should ask the network provider to
enable Calling Line Identification (CLI).
You hear an error tone when keying an input
(a descending tone sequence).
Action has failed/invalid input.
¥ Repeat the operation.
Watch the display and refer to the user guide if
necessary.
You cannot listen to messages on the network
mailbox.
Your PABX is set for dial pulsing.
¥ Set your PABX to tone dialling.
No time is specified for a message in the calls
list.
Date and time have not been set.
¥ Set the date/time (¢page 13).
The answering machine announces "PIN is
incorrect" during remote operation.
1. You have entered the wrong system PIN.
¥ Enter the system PIN again.
2. The system PIN is still set to 0000.
¥ Change the system PIN (¢page 55).
The answering machine is not recording any
messages/has switched over to announce only.
Its memory is full.
¥ Delete old messages.
¥ Play back new messages and delete.
61

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Siemens gigaset e490 twin wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Siemens gigaset e490 twin

Siemens gigaset e490 twin Bedienungsanleitung - Deutsch - 84 seiten

Siemens gigaset e490 twin Bedienungsanleitung - Holländisch - 80 seiten

Siemens gigaset e490 twin Bedienungsanleitung - Französisch - 76 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info