63676
24
Zoom out
Zoom in
Vorherige Seite
1/30
Nächste Seite
23
Appendix
Gigaset HC450 / en / A31008-M1799-R101-2-7619 / Appendix.fm / 08.10.2008
Version 4, 16.09.2005
Appendix
Cleaning
¤ Wipe the HC450 door intercom with a
damp cloth (do not use solvent) or an
antistatic cloth.
Never use a dry cloth. This can cause
static.
Questions and answers
If you have any queries about the use of
your HC450 door intercom, contact us at
www.gigaset.com/customercare
24/7. The table below contains a list of
common problems and possible solutions.
Control unit
HC450 door intercom
If the problem cannot be rectified through
the measures specified, you can reset the
control unit's factory settings. To reset the
factory settings, press the button on the
control unit with a thin object such as a
paper clip for 35 seconds (see diagram on
p. 10).
No function
No power supply.
¥ Check the power supply.
Door opener not working
– no switching noise
Door opener is not correctly connected or does
not conform to the specifications.
¥ Check the installation. Check whether the
door opener is within the supported speci-
fication.
Door opener not working
– switching noise, but door not opening.
Door opener is not within the specification or
not correctly installed mechanically.
¥ Check whether the door opener is within
the supported specification or check the
installation of the door opener (if necessary
adjust).
No function, no keys lighting up
No operating current.
¥ Check the installation, check whether the
connections at the terminals are in the cor-
rect connection sequence.
Door intercom working (bell working), but
not signalling at the mobile phones.
1. Control unit is not registered with the base
station (control unit LED flashing).
¥ Register the control unit.
2. Control unit has been registered but is
dropping the connection (LED flashing).
¥ Reduce the distance between the base
station and the control unit. Install a
repeater if necessary.
Bell not signalling at the mobile phones,
even through the control unit
has a connection to the base station (cont-
rol unit LED lighting up continuously).
1. no int. Ringing is set.
¥ Select a value between 10 and
60 seconds.
2. Call forwarding activated
(display showing "line in use").
¥ Select "Status: Home".
3. Handsets outside of range or switched off,
specifically set handset deregistered or
switched off.
¥ Bring the handsets within the base sta-
tion's range, switch on or charge the
handsets.
¥ Select another handset for signalling or
switch over to "Signal to All Handsets".
Please note:
Any settings you have made will be lost when
you reset the factory settings. You will have to
reregister the control unit, see p. 13.
24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Siemens Gigaset HC450 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Siemens Gigaset HC450

Siemens Gigaset HC450 Bedienungsanleitung - Deutsch - 32 seiten

Siemens Gigaset HC450 Bedienungsanleitung - Holländisch - 30 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info