Bedienungsanleitung Siemens gigaset s455 duo (Seite 52 von 65) (Englisch)

300378

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

Appendix

Gigaset S455 AM / GBR / A31008-M1714-L101-1-7619 / appendix.fm / 31.08.2006

Appendix

Care

¤ Wipe the base station and handset with

a damp cloth (do not use solvent) or an

antistatic cloth.

Never use a dry cloth. This can cause

static.

Contact with liquid

If the handset has come into contact with

liquid:

1. Switch the handset off and remove

the batteries immediately.

2. Allow the liquid to drain from the hand-

set.

3. Pat all parts dry, then place the handset

with the battery compartment open

and the keypad facing down in a dry,

warm place for at least 72 hours (not

in a microwave, oven etc.).

4. Do not switch on the handset again

until it is completely dry.

When it has fully dried out, you will nor-

mally be able to use it again.

Questions and answers

If you have any queries about the use of

your telephone, you can contact us at any

time at www.siemens.com/gigasetcus-

tomercare . The table below contains a list

of common problems and possible solu-

tions.

The display is blank.

1. The handset is not switched on.

¥ Press and hold the end call key a.

2. The batteries are flat.

¥ Charge or replace the batteries (page 8).

The handset does not respond to a key press.

The keypad lock is activated.

¥ Press and hold the hash key

(page 13).

"Base station x" is flashing in the display.

1. The handset is outside the range of the base

station.

¥ Reduce the distance between handset/

base station.

2. The handset has been de-registered.

¥ Register the handset (page 37).

3. The base station is not switched on.

¥ Check the base station mains adapter

(page 6).

Base Search is flashing in the display.

The handset is set for Best Base and no base sta-

tion is switched on or within range.

¥ Reduce the distance between handset/base

station.

¥ Check the base station mains adapter

(page 6).

Handset does not ring.

1. The ringtone is switched off.

¥ Activate the ringtone (page 44).

2. Call diversion set to All Calls.

¥ Switch off Call Diversion (page 16).

You cannot hear a ringtone/dialling tone.

Base station's phone cord has been replaced.

¥ When purchasing a new cord, ensure that it

has the correct pin connections (page 7).

The other party cannot hear you.

You have pressed the

u (INT) key. The hand-

set is "muted".

¥ Switch on the microphone again (page 13).

The incoming call number is not displayed

although CLIP is set.

Phone number identification is not enabled.

¥ Caller should ask network provider to acti-

vate phone number identification (CLI).

You hear an error tone when keying an input

(a descending sequence of tones).

Action has failed/invalid input.

¥ Repeat the operation.

Watch the display and refer to the operating

instructions if necessary.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens gigaset s455 duo Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens gigaset s455 duo

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info