Bedienungsanleitung Siemens LB88574 (Seite 13 von 20) (Englisch)

709281

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Installation instructions en

¡The surfaces of the appliance are sensitive. Avoid

damaging them during installation.

12.6 Instructions for the electrical

connection

In order to safely connect the appliance to the elec-

trical system, follow these instructions.

WARNING‒Risk of electric shock!

It must always be possible to disconnect the appliance

from the electricity supply. The appliance must only be

connected to a protective contact socket that has been

correctly installed.

▶The mains plug for the mains power cable must be

easily accessible after the appliance is installed.

▶If this is not possible, an all-pole isolating switch

must be integrated into the permanent electrical in-

stallation according to the conditions of overvoltage

category III and according to the installation regula-

tions.

▶The permanent electrical installation must only be

wired by a professional electrician. We recommend

installing a residual-current circuit breaker (RCCB)

in the appliance's power supply circuit.

Sharp-edged components inside the appliance may

damage the connecting cable.

▶Do not kink or trap the connecting cable.

¡The connection data can be found on the rating

plate. →Page10

¡The connecting cable is approx.1.30m long.

¡This appliance complies with the EC interference

suppression regulations.

¡The appliance corresponds to protection class 1.

You should therefore only use the appliance with a

protective earth connection.

¡Do not connect the appliance to the power supply

during installation.

¡Ensure that the protection against contact is guaran-

teed during installation.

12.7 Information on the installation situation

¡Install this appliance in a kitchen cupboard.

¡To install additional special accessory parts, ob-

serve the enclosed installation instructions.

¡The width of the extractor hood must correspond at

least with the width of the hob.

¡To optimally detect the cooking vapours, install the

appliance in the middle of the hob.

12.8 Instructions for the exhaust air pipe

The appliance manufacturer does not provide any war-

ranty for faults attributable to the pipeline.

¡Use a short, straight exhaust air pipe with as large a

pipe diameter as possible.

¡Long, rough exhaust air pipes, many pipe bends or

small pipe diameters reduce the suction power and

increase the fan noise.

¡Use an exhaust pipe that is made of non-combust-

ible material.

¡To prevent condensate from returning, fit the ex-

haust pipe with a 1° gradient from the appliance.

Round pipes

Use round pipes with an inner diameter of 150mm (re-

commended) or at least 120mm.

Flat ducts

Use flat ducts with an inner cross-section that corres-

ponds to the diameter of the round pipes:

¡Diameter of 150mm corresponds to ap-

prox.177cm².

¡Diameter of 120mm corresponds to ap-

prox.113cm².

¡Use sealing strips for different pipe diameters.

¡Do not use any flat ducts with sharp bends.

12.9 Instructions for the air extraction mode

For air extraction mode, a one-way flap should be in-

stalled.

Notes

¡If a one-way flap is not included with the appliance,

one can be ordered from a specialist retailer.

¡If the exhaust air is conveyed through the external

wall, a telescopic duct should be used.

12.10 Information about circulating-air

mode

The appliance must only be operated when it is se-

curely installed and the pipework is connected.

12.11 Installation

Checking the unit

1. Check whether the fitted unit is level and has suffi-

cient load-bearing capacity.

The max. weight of the appliance is 10kg.

Note:Note the furniture manufacturer's specifica-

tions with regard to the load-bearing capacity of the

fitted unit.

2. Ensure that the fitted unit is heat-resistant up to

90°C.

3. Ensure that the fitted unit is still stable after the cut-

outs have been made.

Preparing the units

Requirement:The unit is suitable for the installation.

→"Checking the unit", Page13

1. Make the cut-out for the appliance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens LB88574 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens LB88574

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info