Bedienungsanleitung Siemens lc 86 k 950 (Seite 21 von 88) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

132193

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

If you encounter a problem

Note: If the light does not function, check

that the bulbs have been inserted correctly.

If an

≡

≡≡

≡

or [ appears in the display:

See „Filters and maintenance“ Section.

If is not possible to operate the extractor

hood:

Disconnect the extractor hood from the

mains electricity supply by pulling out the

plug or switching it off at the main fuse box.

Wait for approx. 1 minute and then switch it

on again.

If you have any questions or if a fault occurs,

please call Customer Service.

(See list of Customer Service

representatives).

When you call, please quote the following:

AB - Nr.: FD

Enter the relevant numbers into the box

above. The AB - Nr. (product no.) and FD

(production date) are shown on the

nameplate which can be seen inside the

extractor hood after the filter frame has been

detached.

The manufacturer of the extractor hoods

accepts no liability for complaints which can

be attributed to the design and layout of the

pipework.

Installation Instructions:

Important information

Old appliances are not worthless rubbish.

Valuable raw materials can be reclaimed by

recycling old appliances. Before disposing

of your old appliance, render it unusable.

You received your new appliance in a

protective shipping carton. All packaging

materials are environmentally friendly and

recyclable. Please contribute to a better

environment by disposing of packaging

materials in an environmentally-friendly

manner.

Please ask your dealer or inquire at your

local authority about current means of

disposal.

The extractor hood can be used in exhaust

air or circulating air mode.

Always mount the extractor hood over the

centre of the hob.

Minimum distance between electric hob and

bottom edge of extractor hood: 400 mm,

The extractor hood must not be installed over

a solid fuel cooker - a potential fire hazard

(e.g. flying sparks) -unless the cooker

features a closed, non-removable cover

and all national regulations are observed.

The smaller the gap between the extractor

hood and hotplates, the greater the

likelihood that droplets will form on the

underside of the extractor hood.

Additional information concerning gas

cookers:

When installing gas hotplates, comply with

the relevant national statutory regulations

(e.g. in Germany: Technische Regeln Gas-

installation TRGI).

Always comply with the currently valid

regulations and installation instructions

supplied by the gas appliance manufacturer.

Only one side of the extractor hood may be

installed next to a high-sided unit or high

wall. Gap at least 50 mm.

Minimum distance on gas hotplates

between the upper edge of the trivet

and lower edge of the extractor

hood: 550 mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens lc 86 k 950 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info