109985
24
Zoom out
Zoom in
Vorherige Seite
1/52
Nächste Seite
24
en
Electrical connection
Electrical data:
Are to be found on the name plate inside the appli-
ance after removal of the lterframe.
Before undertaking any repairs, always
disconnect the extractor hood from the electricity
supply.
Length of the connecting cable: 1.30 m.
This extractor hood corresponds to EC regulations
concerning RF interference suppression.
Risk of electric shock!
The appliance features an EU safety plug. To ensure
protective earthing in a Danish socket, the appliance
must be connected to a suitable plug adapter. This
adapter (permitted up to max. 13 amps) is available
from customer service (spare part no. 616581).
Installation
1. Draw a line on the wall from the ceiling to the
lower edge of the hood at the centre of the lo-
cation where the hood is going to be mounted.
2. Use the template or following the picture to
mark the points (A-B-C) on the wall where the
screws will be mounted.
Ensure that the minimum distance between the
hob and the extractor hood is maintained 460 mm
for the gas hob and electric hod
Installation
Note: Take into account any special accessories
that are going to be tted.
qTo install a ø 120 mm air exhaust connection,
insert the reducer ange 9 on the hood body
outlet.
qFix the pipe in position using sufcient pipe
clamps (not supplied).
qRemove charcoal lters, if present.


8. Hook the hood body onto the screws 12a into
the holes A.
9. Fully tighten support screws 12a.
10. Adjust screws Vr to level the hood body.
11. Tighten the safety screw 11 in holes B.
Connection in Ducting Version
When installing the ducting version, connect the
hood to the chimney using either a exible or rigid
pipe ø 150 or 120 mm, the choice of which is left to
the installer.


3. Drill ø 8 mm holes A and B for the extractor
hood. Drill ø 8 mm holes C for the chimney
brackets.
4. Insert plugs 11 into the holes A,B and C so that
they are ush with the wall.
5. Fix the brackets 7.2.1 using the screws sup-
plied.
6. Insert not totally the screw into the holes A.
Mounting the hood body
7. Before attaching the hood body, tighten the two
screws Vr located on the hood body mounting
points.
24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Siemens LC 956KA30 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info