Bedienungsanleitung Siemens lc 957 ka 70 (Seite 23 von 88) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

133400

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Prior to installation

For optimum extractor hood efficiency:

Short, smooth air exhaust pipe.

As few bends in the pipe as possible.

Diameter of pipe to be as large as possible

and no tight bends in pipe.

If long, rough exhaust-air pipes, many pipe

bends or smaller pipe diameters are used,

the air extraction rate will no longer be at

an optimum level and there will be an

increase in noise.

The manufacturer of the extractor hoods

accepts no liability for complaints which

can be attributed to the design and layout

of the pipework.

Round pipes:

Internal diameter: 150 mm or bigger.

We recommend internal diameters of

150mm or larger.

Flat ducts must have an internal cross-

section that equates to that of round pipes.

For exhaust-air mode, ensure that there

is an adequate supply of fresh air.

WARNING: THIS APPLIANCE MUST BE

Electrical connection

EARTHED

IMPORTANT: Fitting a Different Plug:

The wires in the mains lead are coloured in

accordance with the following code:

Green and Yellow - Earth

Blue - Neutral

Brown - Live

If you fit your own plug, the colours of these

wires may not correspond with the

identifying marks on the plug terminals.

This is what you have to do:

1. Connect the green and yellow (Earth) wire

to the terminal in the plug marked ‘E’ or

with the symbol, or coloured green or green

and yellow.

2. Connect the blue (Neutral) wire to the ter

minal in the plug marked ‘N’ or coloured

black.

3. Connect the brown (Live) wire to the ter

minal marked ‘L, or coloured red.

The extractor hood should only be

connected to an earthed socket that has

been installed according to relevant

regulations. If possible, site the earthed

socket directly behind the chimney panelling.

Electrical data:

Are to be found on the name plate inside the

appliance after removal of the filter frame.

Before undertaking any repairs,

always disconnect the extractor hood from

the electricity supply.

Length of the connecting cable: 1.30 m.

If it is necessary to wire the extractor hood

directly into the mains:

The extractor hood should only be connected

to the electricity supply by a properly qualified

electrician.

A separator must be installed in the house-

hold circuit. A suitable separator is a switch

that has a contact gap of more than 3 mm

and interrupts all poles. Such devices

include circuit breakers and contactors.

If the connecting cable for this appliance is

damaged, the cable must be replaced by

the manufacturer or his customer service or

a similarly qualified person in order to

prevent serious injury to the user.

This extractor hood corresponds to EC

regulations concerning RF interference

suppression.

In order to avoid damage during

transportation, the front glass panel will be

packaged separately from the hood body

and must be connected to the hood border

after unpacking (see following illustration).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens lc 957 ka 70 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info