Bedienungsanleitung Siemens LC64WA521 (Seite 11 von 16) (Englisch)

623946

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

General information

Exhaust air mode

: Risk of death!

Risk of poisoning from flue gases that are drawn back in. The

exhaust air must not be conveyed into a functioning smoke or

exhaust gas flue or into a shaft which is used to ventilate

installation rooms that contain heating appliances. If the

exhaust air is to be conveyed into a non-functioning smoke or

exhaust gas flue, you must obtain the consent of the heating

engineer responsible.

If the exhaust air is conveyed through the outer wall, a

telescopic wall box should be used.

Exhaust duct

Note: The device manufacturer does not assume any warranty

for complaints attributable to the pipe section.

■ The device achieves its optimum performance by means of a

short, straight exhaust air pipe and as large a pipe diameter

as possible.

■ As a result of long rough exhaust air pipes, many pipe bends

or pipe diameters that are smaller than 150 mm, the optimum

extraction performance is not achieved and fan noise is

increased.

■ The pipes or hoses for laying the exhaust air line must

consist of non-combustible material.

Round pipes

An inner diameter of 150 mm, but at least 120 mm, is

recommended.

Flat ducts

The inner cross-section must correspond to the diameter of the

round pipes.

dia. 150 mm ca. 177 cm

dia. 120 mm ca. 113 cm

■ Flat ducts should not have any sharp deflections.

■ Use sealing strips for deviating pipe diameters.

Checking the wall

■ The wall must be level, vertical and adequately load-bearing.

■ The depth of the bore holes must be the same length as the

screws. The wall plugs must have a secure grip.

■ The enclosed screws and wall plugs are suitable for solid

brickwork. Suitable fasteners must be used for other

structures (e.g. plasterboard, porous concrete, poroton

bricks).

■ The max. weight of the extractor hood is 40 kg.

Electrical connection

: Risk of electric shock!

Components inside the appliance may have sharp edges.

These may damage the connecting cable. Do not kink or pinch

the connecting cable during installation.

The required connection data can be found on the rating plate

inside the appliance; to do this, remove the metal mesh grease

filter.

Length of the cable: approx. 1.30 m

This appliance complies with the EC interference suppression

regulations.

: Risk of electric shock!

It must always be possible to disconnect the appliance from the

electricity supply. The appliance must only be connected to a

protective contact socket which has been correctly installed. If

the plug is no longer accessible following installation of the

appliance, or a fixed connection is required, an all-pole isolating

switch must be present on the installation side with a contact

gap of at least 3 mm. The fixed connection must only be

installed by an electrician.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens LC64WA521 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens LC64WA521

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info