Bedienungsanleitung Siemens LD88WMM66B (Seite 18 von 24) (Englisch)

791180

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

en Installation instructions

¡Include a ventilation opening in the base with a

cross-section of 80 cm².

¡Flush installation is only possible in stone and gran-

ite work surfaces.

17.6 Instructions for the exhaust air pipe

The appliance manufacturer does not provide any war-

ranty for faults attributable to the pipeline.

¡Use a short, straight exhaust air pipe with as large a

pipe diameter as possible.

¡Long, rough exhaust air pipes, many pipe bends or

small pipe diameters reduce the suction power and

increase the fan noise.

¡Use an exhaust pipe that is made of non-combust-

ible material.

¡To prevent condensate from returning, fit the ex-

haust pipe with a 1° gradient from the appliance.

Note:Suitable air extraction ducts are available from

our after-sales service, your dealer or on our website.

Flat ducts

Use flat ducts with an inner cross-section that corres-

ponds to the diameter of the round pipes:

¡Diameter of 150mm corresponds to ap-

prox.177cm².

¡Diameter of 120mm corresponds to ap-

prox.113cm².

¡Use sealing strips for different pipe diameters.

¡Do not use any flat ducts with sharp bends.

Round pipes

Use round pipes with an inner diameter of 150mm (re-

commended) or at least 120mm.

17.7 General information

Follow these general instructions during the installation.

¡For the installation, observe the currently valid build-

ing regulations and the regulations of the local elec-

tricity and gas suppliers.

¡When discharging the exhaust air, the official and

legal regulations, such as the regional building

code., must be observed.

¡In order to freely access the fan box for servicing,

select an easy-to-reach installation site.

¡The surfaces of the appliance are sensitive. Avoid

damaging them during installation.

17.8 Installation

Checking the units

▶Check whether the fitted unit is level and has suffi-

cient load-bearing capacity.

The max. weight of the appliance is 40kg.

Preparing the units

Note:To install the hob and the appliance seamlessly,

you require special accessories, which are not included

in the scope of delivery. Observe the enclosed installa-

tion instructions for special accessories.

Requirement:The unit is suitable for the installation.

1. Make a cut-out in the worktop, depending on the in-

stallation position.

The angle between the cut surface and the worktop

must be 90°.

2. Ensure that the worktop has sufficient load-bearing

capacity and stability.

Use a heat- and humidity-resistant reinforcing mater-

ial for any substructure.

3. Ensure that the fitted unit is still stable after the cut-

outs have been made.

4. Remove any shavings.

5. Depending on the installation position, remove the

back panel of the fitted unit.

Preparing the appliance

WARNING‒Risk of injury!

The appliance is heavy.

▶To move the appliance, twopeople are required.

▶Use only suitable tools and equipment.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens LD88WMM66B Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens LD88WMM66B

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info