Bedienungsanleitung Siemens OpenScape DECT Phone S5 on OpenScape Cordless Enterprise (Seite 35 von 85) (Englisch)

680392

Zoom out

Zoom in

Vorherige Seite

1/85

Nächste Seite

34 Questions and answers

Questions and answers

Manufacturer's advice

Authorization

Depending on the variant, this device is intended for analog phone lines in the German/Luxembourg or

Austrian network (see device label).

Country-specific requirements have been taken into consideration.

We, Unify Software and Solutions GmbH & Co. KG, declare that this device meets the essential requirements and other relevant

regulations laid down in Directive 1999/5/EC.

The EU declaration of conformity for your country under 1999/5/EC can be found at:

wiki.unify.com/wiki/Declarations_of_Conformity#Cordless_Phones.

This declaration may also be available in the files "International Declarations of Conformity" or "European

Declarations of Conformity" in some cases.

Therefore please also read these files.

The display is blank.

• The handset is not switched on. Press and hold

• The battery is empty. Charge the battery or replace it ( p. 8)

"No Base" flashes on the display.

• The handset is outside the range of the base. Reduce the distance between the handset and base

"Please register handset" flashes on the display.

• The handset is not yet registered or was de-registered when another handset was registered.

The handset does not ring.

• The ringtone is deactivated. Activate the ringtone ( p. 31)

• The phone does not ring during a specific period or for certain numbers.

¤ Check the time control for external calls ( p. 21)

The other party cannot hear you.

• The handset is "muted". Reactivate the microphone ( p. 14)

The caller's number is not displayed.

• Calling Line Identification (CLI) is not enabled for the caller. The caller should ask the network

provider to enable Calling Line Identification(CLI).

• Calling Line Identification Presentation (CLIP) is not supported or enabled by the network provider.

Ask the network provider to enable Calling Line Identification Presentation (CLIP).

• The phone is connected via a PABX or a router with an integrated PABX (gateway) that does not forward

all information.

¤ Reset the system: Pull out the power plug briefly. Reinsert the plug and wait until the device restarts.

¤ Check the settings on the PABX and activate phone number display if necessary. To do this, search

for terms such as CLIP, calling line identification, telephone number identification, caller ID, ... in the

system user guide or ask the system manufacturer.

You hear an error tone when keying in (descending tone sequence).

• Action has failed/invalid input. Repeat the process. Read the display and refer to the user guide if

necessary.

No time is specified for a message in the call list.

• The date/time are not set. Set the date and time.

Registration or connection problems with a Bluetooth headset.

¤ Reset the Bluetooth headset (see the user guide for the headset).

¤ Delete the registration data on the handset by de-registering the device ( p. 24).

¤ Repeat the registration process ( p. 25).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens OpenScape DECT Phone S5 on OpenScape Cordless Enterprise Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info