Bedienungsanleitung Siemens optiPoint 500 entry (Seite 75 von 78) (Englisch)

35938

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

FCC and Industry Canada Compliance

This section describes the requirements for compliance with Federal Communications

Commission (FCC) Rules and Industry Canada CS-03 standard.

FCC Certification and Requirements

The following paragraphs describe requirements and information based on FCC rules.

Service

If you experience problem with the Siemens optiPoint telephone, contact Siemens cus-

tomer support at 1-800-835-7656 for information on service and repairs. The telephone

company can ask you to disconnect the equipment from the network until the problem is

corrected or until you are sure that the equipment is not malfunctioning.

FCC Rules, Part 15

The Siemens optiPoint telephone has been tested and complied with the limits for a class

A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequen-

cy energy and, if not installed and used in accordance with the instruction manual, can

cause harmful interference to radio communications. Operation of this equipment in a res-

idential area is likely to cause harmful interference, in which case the user will be required

to correct the interference in the user’s expense.

FCC Rules, Part 68

FCC Part 68 Certification

The Siemens optiPoint telephone is certified with FCC under Part 68 as a component de-

vice for connection behind FCC Part 68 certified Siemens PBX systems. In order for the

FCC certification of the Siemens optiPoint telephone to be retained, all other products

used in conjunction with the Siemens optiPoint telephone must also be FCC Part 68 certi-

fied for use with the front-end terminal equipment. If any of these components are not cer-

tified, Siemens is required to obtain FCC Part 68 certification of the assembled equipment

prior to connection to the telephone network. Part 68 certification requires Siemens to

maintain this approval and as such are responsible for the following:

– Any component added to the Siemens optiPoint telephone, whether it bears compo-

nent certification or not, will require a Part 68 compliance evaluation. Siemens may

need to test and make a modification filing to the FCC before that new component

can be used;

– Any modification/update made to the Siemens optiPoint telephone will require a Part

68 compliance evaluation. Siemens may need to test and make a modification filing

to the FCC before that modified component can be used;

– Siemens optiPoint telephone complies with and will continue to comply with all the

applicable rules and regulations in Subpart D of the FCC Part 68 rules during the life-

time of the product.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens optiPoint 500 entry Seite 75

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens optiPoint 500 entry

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info