Bedienungsanleitung Siemens RCR10-868 (Seite 1 von 2) (Englisch)

620391

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

REV24RF..

Operating instructions RCR10/868

REV24RF.. - 7-day radio room temperature controller for the right temperature at the right time. All factory

settings already provide optimal living comfort. You can easily adjust the controller to your needs with the user-

assisted clear-text display and program selection slider.

REV24RF.. (controller with radio transmitter) is a wireless device that you can mount on the wall or place freely

on a base in the room.

Its radio frequency 868 MHz is largely immune to external disturbances. The signal level meets regulations and

is kept as low as possible. The devices are approved for all EU member states, Iceland, Norway, and

Switzerland.

Note the following for placing the devices:

• Make sure no other influencing factors influence the controller's temperature sensor (no solar radiation and

other heat or cold source influences).

• The distance between controller and receiver may not exceed 20 m or 2 floors.

• Do not place near metallic items or electrical devices, etc..

Day of week

Low battery

Radio clock Date Setting: 1-5, 6-7, 1..7

active Reading: 1..7

Time display

Holiday mode

Display

Info mode

Test mode

Installer mode

Temperature

setpoint symbols

Text display

Alarm

Cooling mode /

Heating mode

Switching pattern

with time cursor

Automatic mode

Party mode active

Exception day mode

Continuous comfort mode

°C or °F

Continuous energy

saving mode

Heating On /

Cooling On

Protection mode

Temperature display

Info button

Increase values, set time or

make a selection

Change between Comfort and

energy saving temperature

(active until next switching time)

and Part

function

Decrease values, set time or

make a selection

Operating mode

selector:

- Automatic

- Exception day

- Comfort mode

- Energy saving

mode

- Prot. mode

Program selection slider

RUN

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

Operating elements and settings

Time setting

Date

Day / Month / Year

Weekdays 1-5

Weekend 6-7

Individual. da

s 1..7

1, 2 or 3

Comfort phases

Start time

Comfort phase 1

Temperature

Comfort phase 1

End

Comfort phase 1

Start time

Comfort phase 2

Temperature

Comfort phase 2

End

Comfort phase 2

Start time

Comfort phase 3

Temperature

Comfort phase 3

End

Comfort phase 3

Saving temp. time

program

Start

Absence

Temperature

Absence

End

Absence

Slider positions

If the selected operating mode does not support the setting, the time display shows PASS.

Special symbols displayed

The controller display can show the following special symbols:

Is symbol displayed ?

The alarm indicates an error!

Press the Info button and check the error message (e.g. radio clock signal, radio connection to receiver, etc.).

Contact a specialist as needed.

Is symbol or displayed?

The controller is in "heating mode“ or "cooling mode“ .

Is a rolling triangle symbol displayed ?

The controller sends a control telegram to the receiver.

Is symbol displayed ?

This symbol tells you that you must exchange the batteries within the next 3

months.

Insert 2 new alkaline batteries type AA, 1.5 V as follows:

Remove the controller from the mounting base; open the battery compartment on the

rear; remove the old batteries; insert the new batteries and reinsert the controller in

the base.

Caution: Time and date are retained for max. 1 minute.

(All other settings remain unchanged).

Dispose of the batteries as per regulations.

Is symbol displayed ?

The radio clock symbol only appears if the receiver is set up and activated to receive the

time signal from Frankfurt (Germany). A permanent symbol indicates that both time and

date of the controller are synchronized to Frankfurt (DCF77).

The symbol flashes if the signal is not received for more than 1 week.

Commission receiver RCR10/868

LED_1 LED_2

The factory setting connects the receiver in the RF/SET to the controller.

After commissioning, it does not require maintenance.

Press the override button on the receiver to manually override the

relay. After ca. 15 minutes, the relay again follows the controller's control

telegrams.

The relay turns off after a voltage interruption as well as 60 minutes after

receipt of the last control telegram.

Receiver and controller can be manually connected. Press button

“LEARN“ for ca. 4 seconds on the receiver: The blue LED_2 flashes

slowly, learning mode is active. Press button "LEARN" within 20 minutes

on the controller for ca. 4 seconds: The blue LED_2 briefly flashes

quickly; LED_1 goes from red to green.

Max 15 receivers can be connected to 1 controller.

Commission the controller and quick start

The controller contains a factory-set comfort switching pattern and temperature values.

Proceed as follows for initial commissioning:

Remove the controller from the mounting base and pull off the black insulating

tape from the 2 batteries: The controller turns on automatically. Reinsert the

controller in the mounting base.

After startup, a welcome message appears for ca. 2 minutes. Press a button

to interrupt the message. Language selection starts with “ENGLISH“ (factory

setting). Press

or until your language appears. Press or move

the slider to accept your language.

Slider in position 1 (time setting): Press or to set the time.

Note: No entry if there is a time signal receiver (DCF77).

Slider in position 2 (date: day/month/year): Press

or to set the date.

Note: No entry if there is a time signal receiver (DCF77).

RUN

Move the slider to the very right to position RUN (only way to close the cover).

Set the operating mode with the operating mode selector. Factory setting .

Fold the operating instructions and reinsert in the mounting base.

Tips to save energy without reducing comfort

• Heat your rooms to max 21 °C.

• Use to switch to energy saving temperature even if you are absent only briefly.

• Air out your rooms briefly, but with wide-open windows.

B2206en 25.12.2007 Siemens, Building Technologies

Siemens RCR10-868 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens RCR10-868

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info