Bedienungsanleitung Siemens RCR10-868 (Seite 10 von 56) (Alle Sprachen)

620391

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

10/56 2015-03-18 CE1G2206xx

The expert level is quit by pressing the operating mode selection button .

Code list

Function block Code Name Factory setting Your setting

Basic settings

00 Language English

01 Sensor calibration off

02 Switching differential 0.5 °C

LCD settings

10 Illumination time 10 seconds

11 Background brightness 0

12 Contrast 0

Clock settings

Time zone

Deviation from time signal received from Frankfurt

(Central European Time CET) (refer to Note 1)

0 hours

31 Start of summer time (refer to Note 2) March 31 (31-03)

32 End of summer time (refer to Note 3) October 31 (31-10)

Note 1: If the radio clock is not active or not present, this setting has no impact.

With the radio clock active, the time signal received from Frankfurt is shifted by the value set under code 30 (time zone).

Note 2: If the radio clock is not active or not present, the time change always takes place at 02:00 on the Sunday before the set date.

With the radio clock active, the time change is shifted by the value set under code 30 (time zone).

Note 3: If the radio clock is not active or not present, the time change always takes place at 03:00 on the Sunday before the set date.

With the radio clock active, the time change is shifted by the value set under code 30 (time zone).

3 Function check

a) Check the display. If there is no display, check the batteries

b) “Continuously Comfort mode“

, read the temperature displayed

c) REV.. in heating mode: Set the temperature setpoint to a level above the

displayed room temperature (see operating instructions).

REV.. in cooling mode: Set the temperature setpoint to a level below the

displayed room temperature (see operating instructions).

d) The relay and thus the actuating device must respond within

1 minute. Symbol ▲ appears on the display. If not:

· Check actuating device and wiring

· In heating mode, the room temperature is possibly higher than the

adjusted temperature setpoint, in cooling mode possibly lower

e) Set temperature setpoint of “Continuously Comfort mode“ to the

required level

f) Select the required operating mode

4 Reset

User-defined settings:

Press simultaneously

, and for 3 seconds:

All temperature and time settings of the slider positions are reset to their default

values (refer to section “Factory settings“ in the operating instructions). The

settings made on the expert level will remain unchanged.

The clock starts at 12:00, the date on 01-01-08

(01 - January - 2008). During the reset time, all sectors of the display are

illuminated and can thus be checked.

All user-defined settings plus those made on the expert level:

Press simultaneously the DIP switch reset button, and for 5

seconds:

After this reset, all factory settings will be reloaded. This applies to both the

slider settings and the settings made on the expert level.

Notes

· The controller is classified as a device of software class A and designed

for use in environments with normal degree of pollution

· REV24RF/SET is a set of units consisting of electronic room temperature

controller with 7-day time switch, RF transmitter (REV24RF..) and RF

receiver (RCR10/868)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens RCR10-868 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens RCR10-868

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info