Bedienungsanleitung Siemens RDD310-EH (Seite 1 von 2) (Englisch)

620368

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

CB1B1440en / 2013-09-12 Subject to change Siemens Building Technologies 4/4

Control parameters

If you want to change the control parameters, proceed as follows:

+ / –

1. Set the thermostat to Frost Protection mode

2. Press + and – simultaneously for at least 3 seconds.

Release the buttons and, within 2 seconds, press – again for 7 seconds. The display will show "P02".

3. Select the required parameter by repeatedly pressing + or – .

4. Press + and – simultaneously. The current value of the selected parameter starts to flash. Adjust it by

pressing + or – .

5. Press + and – simultaneously again to display the next parameter.

6. If you wish to display and change additional parameters, repeat steps 3 through 5.

7. Service or expert level: 10 seconds after the last display or setting, all changes are stored and the

thermostat will leave the parameter setting mode.

Expert level: Press + or – until "End" is displayed. Then, press + and – simultaneously to save the change

and exit the parameter setting mode.

No.

Thermostat’s parameter Factory setting Setting range



P02 Selection of operating mode via operating mode

button

1 = Frost Protection –

Comfort mode

RDD310/EH:

1 = Comfort - Frost

Protection

2 = Comfort - Economy -

Frost Protection

RDE410/EH:

1 = Auto - Comfort -

Frost Protection

2 = Auto - Comfort -

Economy - Frost

Protection

P05 Temperature sensor calibration 0.0 °C -3…3 °C

P06 Standard temperature display 0 = Room

temperature

0 = Room temperature

1 = setpoint

P08 Comfort basic setpoint 20 °C 5...40 °C

P09 Min. setpoint limitation in Comfort mode (Wmin

Comf

) 5 °C 5...40 °C

P10 Max. setpoint limitation in Comfort mode (Wmax

Comf

) 35 °C 5...40 °C

P11 Heating setpoint in Economy mode 16 °C Off, 5…18 °C

P14 Button lock (press operating mode button for

3 seconds to lock or unlock)

0 = Disabled 0 = Disabled

1 = Auto lock

2 = Manual lock

P30 Switching differential in heating mode 1 K 0.5…6 K

P38 External input 0 0 = No input

1 = External sensor

input

P45 Heating system load in kW 2.8 kW 0…3.6 kW

P51 Floor heating temperature limit Off Off, 10...60 °C

P65 Setpoint of heating in Frost Protection mode (Wheat

Stb

)

8 °C Off, 5…18 °C

P69 Temporary setpoint in Comfort mode Off Off = Disabled

On = Enabled

P71 Reloading factory settings

Set value to "On" and confirm by pressing + and –

Off Off = Idle

On = Reset

d02 Status X1 Diagnostics 0…xx °C = Measured

temperature

d07 Software version information No adjustment

(All temperature settings can be made in increments of 0.5 °C with the exception of P51, which is in 1 °C)

 Please write down all changes you make!

1/4 CB1B1440en / 2013-09-12 Subject to change Siemens Building Technologies

Operating Instructions

RDD310/EH, RDE410/EH

RDD310/EH and RDE410/EH – the room thermostats for use with electrical floor heating systems. The products feature a

built-in room sensor to control the room temperature, and the user can connect a cable temperature sensor to limit the

maximum floor temperature. The thermostat provides Comfort, Economy and Frost Protection mode. The RDE410/EH also

features an Auto Timer with 8 programmable time switches. You can either rely on the factory settings or make adjustments

that suit your individual needs.

Are your rooms too warm or too cold?

+ / –

Press + or – to increase or decrease the current room temperature setpoint in increments of 0.5 C for

Comfort mode. 5 seconds after the last push, the room temperature setpoint is automatically saved. The

display stops flashing and shows the room temperature currently measured.

The maximum setpoint setting range is 5...40 °C, unless limited by parameters P09 and P10.

Do you require continuous Comfort mode?

Press the operating mode button

to switch to Comfort mode . In that case, the room temperature

setpoint is always maintained at the Comfort level.

The RDE410/EH has a dedicated

button for selection of the operating mode.

Display

Operation and settings

Buttons locked

Heating demand

Measured room temperature,

setpoints and parameters

Symbol when current room

temperature is displayed

Current time of day *

Colder/Warmer

Weekday 1…7 (1 = Monday/7 = Sunday)*

Confirmation

of settings

View and set Auto Timer

programs

Frost Protection/

system On

RDD310/EH

RDE410/EH

* RDE410/EH only

Time of day and weekday

Selection of operating mode

– Auto Timer ( )

– Comfort ( )

– Economy (

)**

Selection of operating mode

- Frost Protection (

)

- Comfort ( )

- Economy ( ) **

Frost Protection mode

Comfort mode

Economy mode

Auto Timer mode *

Colder/Warmer

** If configured by your HVAC installer

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens RDD310-EH Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens RDD310-EH

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info