Bedienungsanleitung Siemens RDE-MZ6 (Seite 2 von 3) (Englisch)

555887

Zoom out

Zoom in

Vorherige Seite

1/3

Nächste Seite

2/3 Operating Instructions CB1B1428en_01 / 2013-07-05 Siemens Building Technologies

How to pair transmitter and RDE-MZ6

Make sure RDD100.1RF or RDE100.1RF (thermostat(s)/

transmitter(s)) are on your hands.

Option 1: One transmitter for one zone on RDE-MZ6

Learn

Mode

–

To pair one transmitter to one zone, proceed

as follows:

Transmitter setting:

1) On the transmitter, enter the parameter

settings (refer to section "Do you want to

change parameters?" in RDE100.1RFS or

RDD100.1RFS Operating Instructions).

2) Assign the transmitter to the following

specific zone and ensure the parameter

number is set as follows:

Zone no. 1 on transmitter, adjust P19=1

Zone no. 2 on transmitter, adjust P19=2

Zone no. 3 on transmitter, adjust P19=3

Zone no. 4 on transmitter, adjust P19=4

Zone no. 5 on transmitter, adjust P19=5

Zone no. 6 on transmitter, adjust P19=6

RDE-MZ6 receiver setting:

3) Power on the receiver.

4) Press and hold the LEARN button of the

respective channel/zone you want to learn

on RDE-MZ6 for at least 3 seconds, then

release it.

5) The red and green LEDs flash alternately

on the respective channel/zone to indicate

this channel is in learning mode.

Initiate learning:

6) On the transmitter, enter the parameter

settings once again.

7) Proceed to parameter P20. Adjust the

value to P20=1 (ON), then confirm.

8) During wireless learning, the LCD displays

"rF" and "Lrn". Wait for time out and the

transmitter exits the parameter settings.

Successful wireless learning:

9) The green LED flashes for 10 minutes to

indicate that the paired channel has

successfully completed wireless learning.

Recommendation:

10) Additional test to ensure the wireless

signal is fine:

On the transmitter, change the operating

mode by pressing Mode

or change the

setpoint by pressing

+ or –. On the paired

channel, the green LED should flash for 3

seconds before changing to constantly

green. At the same time, observe your

radiator, boiler or heater indication (if it has

one) to ensure that it changed the

operating mode.

11) If step 9 or 10 is working fine, this means

you have successfully paired the zone.

Repeat the same steps above if you want to

pair additional available transmitters

individually.

Unsuccessful wireless learning:

12) If the channel fails to receive wireless data,

the red LED starts to flash **.

13) Repeat steps 1 to 10 until pairing is

successful.

Note:

Always start receiver learning before starting

pairing with the transmitter.

The units must be placed such that transmitter

and received signals have limited external

wireless interference.

**In normal operation, if a drop in wireless

communication occurs due to unforseeable

noise, just leave the receiver and it will recover

automatically.

The pairs are saved even if there is a power shut

down. Communication restarts automatically after

several minutes without any user action.

Option 2: One transmitter for more zones on RDE-MZ6

Learn

Mode

–

To pair a single transmitter to more zones on

the RDE-MZ6, proceed as follows:

Transmitter setting:

1) On the transmitter, enter the parameter

settings (refer to section "Do you want to

change parameters?" in RDE100.1RFS or

RDD100.1RFS Operation Instructions).

2) Assign the transmitter to the following

specific zone and ensure the parameter

number is set as follows:

Zone no. 1 on transmitter, adjust P19=1

RDE-MZ6 receiver setting:

3) Press and hold LEARN button of the

multiple channels/zones you want to learn

on RDE-MZ6 for at least 3 seconds, then

release them.

Example: If you want to assign zone 1, 2

and 3 of the RDE-MZ6 to zone 1 of the

transmitter, press zone 1, 2 and 3 LEARN

button on the receiver simultaneously.

Observe that the LEDs of zone 1, 2 and 3

flash alternately in red and green which

means all 3 channels are in learning mode.

Initiate learning:

4) On the transmitter, enter the parameter

settings once again.

5) Proceed to parameter P20. Set the value to

P20=1 (ON), then confirm.

6) During wireless learning, the LCD displays

"rF" and "Lrn". Wait for time out and the

transmitter exits the parameter settings.

Summary above:

Zone 1 on the transmitter can control zone 1, 2

and 3 of the RDE-MZ6.

Note:

To check successful learning, refer to step 9-

10 of the previous section.

How to reset the ID of the zone?

Reset Reset all zones

If the RDE-MZ6 is not in learning mode, press

and hold the RESET button for more than 10

seconds to reset all IDs of all 6 zones. 6

green LEDs flash for 5 seconds and then

extinguish (recommended for first time setup).

Reset one zone

Press and hold the RESET button and the

respective zone button for more than 10

seconds. This only resets the specific zone.

The green LED of the channel flashes for 5

seconds and then extinguishes; the respective

zone ID is reset.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens RDE-MZ6 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens RDE-MZ6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info