Bedienungsanleitung Siemens RDF 210 (Seite 1 von 2) (Englisch)

485934

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Operating Instructions

RDF210…

CE1B3058en / 17.11.2005 Subject to alteration Building Technologies / HVAC Products

RDF210... – the temperature controller that allows you to set the ideal room temperature you want. The controller provides normal operation or

auto timer mode with 8 programmable timers. The fan operates either in automatic mode or at the selected speed when using manual mode. You

can either rely on the factory settings or make adjustments that suit your individual needs.

Operation

Warmer / colder

setting the

temperature setpoints

and the time of day

Button for changing of

fan operating and standby

- Standby ( )

- Automatic fan speed (

AUTO)

- Manual fan speed ( )

3058Z01en

Display

Button operating mode

- Normal operation ( )

- Auto timer mode ( )

Weekday 1...7

(1 = Monday / 7 = Sunday)

Measured room temperature,

setpoints and parameters

Current time of day

Confirmation

Settings

Heating / cooling

changeover button

Only available with RDF210.2, to change

manually between heating and cooling mode

Auto timer program

Normal operation

Energy saving mode

Standby

Actual room temperature symbol

°C

Temperature

°F

Temperature

AM / PM

(for 12-hour mode)

AUTO

Auto timer mode

Heating mode

Cooling mode

Auto

Automatic fan active

Time of day

1...7

Weekday

Infrared receiver for

remote control

optional with

RDF210.../IR

AUTO

Low fan speed

Medium fan speed

High fan speed

AUTO

Setting the time of day and the weekday

1. Keep the button pressed until the time digits start to flash and then press or to set the time of day. If the current

time is the 24-hour format and you wish to change to the 12-hour format, press

passing 23:59 or press passing 00:00.

Vice versa back to the 24-hour format.

2. Confirm the time of day by pressing

and the weekday indicator starts to flash.

3. Press

or to set the current weekday.

4. Confirm the current weekday by pressing

Are your rooms too warm or too cold?

Do you want to set your controller to standby?

Press the button several times until the display shows the symbol to

indicate that standby is selected.

In standby

, the controller maintains the adjusted lower setpoint of heating

(parameter P03) or the higher setpoint of cooling (parameter P04).

Important:

If the setpoint of standby is set to OFF (factory setting), the controller will not be

active in standby.

Risk of frost!

Do you want to change the fan mode?

AUTO

Press the button until you have selected the desired fan mode.

In automatic mode, the fan speed is automatically selected by the controller and

depends on the setpoint and the actual room temperature. When the room

temperature has reached the setpoint, the fan switches off.

In manual mode the fan operates independently and always runs at the same speed:

Low, medium or high.

The actual fan speed is indicated by the number of fan symbols.

Low fan speed

Medium fan speed

High fan speed

Do you want to change from heating to cooling mode?

With the RDF210, the changeover between cooling and heating is done either

automatically by a heating / cooling changeover sensor or a remote changeover

switch. If the controller is commissioned cooling only or heating only, no changeover

is possible (see parameter P22; factory setting cooling only).

With the RDF210.2, when pressing the

button, the controller changes from

heating to cooling or vice versa.

Do you want to change to auto timer mode?

AUTO

Press the

AUTO

button once to select auto timer mode . In auto timer mode, the

controller will automatically change over between normal operation and energy saving

mode according to the 8 preprogrammed timers.

Do you want to set the programmable timer settings?

A..

To adjust the time schedule, keep the button pressed for 3 seconds to go to

the programmable timer setting mode.

This mode is indicated by displaying Ax (x= auto timer 1...8) and the time xx:xx

flashing. For each auto timer, proceed as follows:

1. The

and symbols are displayed. Press or to adjust the normal

operation start time and confirm by pressing

2. The

and symbols are displayed. Press or to adjust the normal

operation end time or energy saving start time respectively and confirm by

pressing

3. Symbol

will flash. Press or to select or deselect each day and

advance to the next day. Confirm setting for actual timer by pressing

and advance to the next timer

The controller will leave the programmable timer setting mode if no button is pressed

within 20 seconds. All changes made after the last press of

button will not be

saved.

Only applicable in normal operation.

Pressing

or allows you to increase or decrease the current room temperature setpoint for normal operation in

increments of 0.5 °C. The maximum setting range is from 5...40 °C, unless it is limited by parameters P05 and P06.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens RDF 210 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens RDF 210

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info