Bedienungsanleitung Siemens RDF301 (Seite 19 von 82) (Englisch)

555884

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

19 / 82

Siemens RDF301, RDF301.50, RDF600KN Basic documentation CE1P3171en

Building Technologies Functions 2012-10-04

3.3 Room temperature setpoints

3.3.1 Description

The factory setting for the Comfort basic setpoint is 21 °C and can be changed in

the thermostat’s EEPROM via parameter P08 or via bus with communication object

" Comfort basic setpoint". The last intervention always wins.

The Comfort setpoint can be adjusted via the +/- buttons,

or via bus from a remote device like a touchpanel, operating unit, etc.

The last intervention always wins.

If the “Temporary setpoint” function is enabled via parameter P69, the Comfort

setpoint adjusted via the +/- buttons or via bus is set back to the Comfort basic

setpoint stored in P08 when the operating mode changes.

For comfort or energy saving purposes, the setpoint setting range can be limited to

minimum (P09) and maximum (P10).

 If the minimum limit P09 is set lower than the maximum limit P10, both heating

and cooling are adjustable between these 2 limits

 The customer adjusts the desired setpoint and the thermostat controls the room

temperature accordingly.

 For 4-pipe applications *), the selected comfort setpoint is in the middle of the

dead zone (P33). The unit stops to energize the heating / cooling outputs as

soon as the room temperature reaches the dead zone.

Example

5°C 40°C25°C18°C

P10P09

Cooling setpoint adjustable 18…25 °C

Heating setpoint adjustable 18…25 °C

 If the minimum limit P09 is set higher than the limit P10, then

– The setting range of cooling setpoint is from P09…40 °C in place of 5…40 °C

– The setting range of heating setpoint is from 5…P10 °C in place of 5…40 °C.

This allows the user to limit the maximum heating setpoint and the minimum

cooling setpoint. This concept helps to save energy costs.

 For 4-pipe applications *):

– The thermostat runs with the setpoint of the active sequence:

In heating mode, the heating setpoint is active and adjustable via rotary knob.

In cooling mode, the cooling setpoint is active and adjustable via rotary knob.

– Switching from the heating setpoint to the cooling setpoint and vice-versa

occurs when the room temperature reaches the adjusted limitation (P09 or

P10) of the inactive sequence. E.g. the thermostat is in heating sequence

and runs with the heating setpoint. When the room temperature reaches P09,

the thermostat switches to cooling mode and runs with the cooling setpoint, as

long as the room temperature does not drop below P10.

Example

5°C 40°C25°C21°C

P09P10

Cooling setpoint adjustable 25…40 °C

Heating setpoint adjustable 5…21 °C

For heating and cooling applications (e.g. 4-pipe):

– P09 is the setpoint for cooling and P10 the setpoint for heating

– The setpoint can not be adjusted via the rotary knob

Comfort mode

Temporary setpoint

Setpoint limitation

P09 < P10

(comfort concept)

P09 ≥ P10

(energy saving concept)

*) Note: RDF301...

for 4-pipe with P09 ≥ P10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens RDF301 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens RDF301

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info