Bedienungsanleitung Siemens RDF600 (Seite 2 von 2) (Englisch)

555886

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

CE1B3176.3en / 2012-08-29 Subject to change Siemens Building Technologies

Button lock

Press operating mode button

for 3 seconds to lock or unlock the buttons if

manual button lock is configured (parameter P14 = 2).

The thermostat automatically locks the buttons 30 seconds after the last

adjustment if "Auto lock" is configured (P14 = 1).

The key symbol

indicates locked buttons.

Reminder to clean filters

External faults

Commissioning (by qualifie

d HVAC installer)

To adapt the thermostat to your system and optimize the control performance, a number

of control parameters can be adjusted. This can also be made during operation without

opening the thermostat.

Control sequence

Recalibrating the sensor

Note: Economy mode

The Economy setpoints are factory-set to 15 °C for heating and 30 °C for

cooling. Use parameters P11 and P12 to adjust the values.

Important: You can set these setpoints to OFF; the thermostat then is

inactive, i.e. no protective heating or cooling function.  Risk of frost!

Control parameters

Proceed as follows to change the most important control parameters:

(Your HVAC installer can set additional parameters)

+ / -

1. Set the thermostat to Protection

2. Press - and + simultaneously for a minimum of 4 seconds.

Release them and, within 2 seconds, press + again until "P01" is displayed.

3. Repeatedly press the + or – button to select the required parameter.

P01 P02 P08 P13

+-+

3057z03

P14

P12

4. Press + and – simultaneously, the current value of the selected parameter starts to flash, allowing you to change

the value by repeatedly pressing + or –.

5. The next parameter is displayed when you press + and – again simultaneously.

6. Repeat steps 3 to 5 to display and change additional parameters.

7. 15 seconds after the last display or setting, all changes are saved and the thermostat will leave parameter entry

mode.

Para-

meter

Description

Factory setting Setting range



P01 Control sequence

2-pipe: [0…3]

1 (Cooling only)

4-pipe: [2…4]

4 (Heating & Cooling)

0 = Heating only

1 = Cooling only

2 = Manual H or C

3 = Auto Changeover

4 = Heating & cooling

P02 Mode selection by user via operating mode button 1 (Protection,

Comfort)

1 = Protection, Comfort,

2 = Protection, Comfort,

Economy

P04 Selection of °C or °F 0 (°C) 0 = °C

1 = °F

P05 Sensor calibration 0.0 K – 3 ... +3 K

P06 Standard temperature display 0 (Room temp.) 0 = Room temperature

1 = Setpoint

P07 Additional user information 0 (no display) 0 = no display

1 = Temp in °C / °F

P08 Comfort basic setpoint 21 °C 5 ... 40 °C

P09 Minimum setpoint limitation in Comfort (WminComf) 5 °C 5 ... 40 °C

P10 Maximum setpoint limitation in Comfort (WmaxComf) 35 °C 5 ... 40 °C

P11 Setpoint of heating in Economy mode (WheatEco) 15 °C OFF, 5 °C…WcoolEco

P12 Setpoint of cooling in Economy mode (WcoolEco) 30 °C OFF, WheatEco…40°C

P13 Electric heater in cooling mode ON OFF = Disabled

ON = Enabled

P14

Button lock

(Press operating mode button

for 3 seconds to lock or

unlock the buttons)

0 (Disabled) 0 = Disabled

1 = Auto lock

2 = Manual lock

The control parameters displayed depend on the DIP switch settings made

 Please record all changes you make!

(All temperature settings can be made in increments of 0.5 K)

FIL

This message reminds you to clean the filter on your HVAC equipment.

It will appear after  __________ "fan operating hours" and disappear when

the thermostat is set to Protection (

This reminder must be configured by your HVAC installer.

AL1

AL2

This alarm message tells you an external alarm has occurred:

AL1 : ______________________

AL2 : ______________________

The alarms are configured by your HVAC installer

The thermostat can be used in systems either for heating only or cooling

only, manually selection of heating or cooling, or automatic heating / cooling

changeover. Depending on the selected application, the relevant modes are

available and can be adjusted by commissioning parameter P01 if needed.

The factory setting for 2-pipe application is "Cooling only", and for 4 pipe

application "Heating and Cooling"

If the room temperature displayed by the thermostat does not agree with the

temp

erature effectively measured (after min 1 hour of operation), the tem-

perature sensor can be recalibrated. With parameter P05 the temperature can

be adjusted by + or – 0.5 °C up to a maximum of + / - 3 °C.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens RDF600 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens RDF600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info