Bedienungsanleitung Siemens RDG100KN (Seite 1 von 2) (Englisch)

555882

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Operating Instructions

RDG100KN

RDG160KN

RDG165KN

RDG100KN / RDG160KN / RDG165KN – the room thermostat with KNX communications that allows

you to set the ideal room temperature you want. The thermostat provides Comfort, Economy and

Protection mode.

In addition it can operate in Auto timer mode according to a schedule via KNX bus.

The fan operates either in Automatic mode or at the selected speed when using Manual mode.

You can either rely on the factory settings or make adjustments that suit your individual needs.

Humidity control is available on RDG165KN.

Main display Operating mode

Room temperature

Heating mode

Outdoor temperature

Electric heater active

Room temperature in degrees

Celsius

Cooling mode

Room temperature in degrees

Fahrenheit

Comfort mode

Humidity

Economy mode

Button lock active

Auto timer mode

Fault indicator *

Protection mode:

Protection against frost

Condensation in the room *

Humidity control active

Indicator for mode selection

Timer function active

Weekday 1 = Monday

7 = Sunday

Additional user info, e.g.

current time of day, or

rel. humidity

Fan mode

Escape (Cancel)

Automatic fan

Confirm (OK)

Manual fan:

Low Medium High

Operating mode button

Fan mode button

Rotary knob

* Needs to be configured by your HVAC installer

Changing the room temperature

•

Turn the rotary knob clockwise (+) to increase, or counterclockwise (-) to decrease

the current room temperature setpoint. The thermostat changes to Comfort

The setting range is from 5...40 °C; it can be limited by parameters P09 and P10.

(for parameter settings, see reverse side).

Adjusting the fan speed

Low Medium High

•

Press the right button repeatedly until the desired fan mode is reached.

•

In Automatic mode , the fan speed is automatically selected by the thermostat

depending on the setpoint and the actual room temperature.

–

RDG100KN: When the room temperature reaches the setpoint, the fan keeps

running at low speed (factory setting).

– RDG16..KN: The fan stops (factory setting) or keeps running at low speed (P15).

•

In Manual mode, the fan operates independently and always runs at the speed

you set: low / medium / high.

Note:

If desired, you can change the fan mode selector option via P03: Auto / manual, Manual only, or

Manual including Protection mode.

Changing the operating mode of the thermostat

Press the operating mode button repeatedly until the symbol points to the operating

mode you desire.

1. Protection mode

•

In protection mode, the plant stops operating. However, if the room temperature

falls below 8 °C, heating is switched on to protect the room against frost.

•

RDG165KN: the thermostat switches to protection mode when the window

contact (local or on KNX) is active.

The setpoints for Protection mode can be changed by your HVAC installer if desired:

Changes made by installer:  Frost protection: _________ ˚C Heat protection: __________˚C

2. Comfort mode

•

In Comfort mode, the thermostat maintains the room temperature on the setpoint

which can be adjusted with the rotary knob.

•

RDG165KN: the thermostat switches to Comfort mode when the presence detector

(local or on KNX) is active (room is occupied).

3. Auto Timer mode

•

In Auto Timer mode, the thermostat automatically switches over between Comfort

and Economy mode according to the schedule via KNX bus.

If no schedule via KNX is available, then Auto Timer is replaced by Comfort.

4. Economy mode

•

In Economy mode, the thermostat maintains the room temperature at a lower or

higher setpoint, thus saving energy and money.

•

The thermostat can be set to Economy mode either by pressing the operating

mode button if enabled (P02 = 2), or via an external signal (switch or KNX bus

command) such as window switch (RDG1..0KN), keycard or presence detector.

•

The Economy setpoints are factory-set to 15 °C for heating and 30 °C for cooling.

They can be adjusted via parameters P11 and P12 (for parameter settings, see

reverse side).

Important: These setpoints can be set to OFF; which means that the thermostat

is not active, i.e. no protective heating or cooling function. Risk of frost!

Changing from heating to cooling mode

•

The changeover from heating to cooling (or vice versa) is made

– either automatically

by a changeover sensor, or a changeover switch, or a

remote changeover switch via KNX command.

– or manually by pressing the operating mode button.

If the thermostat is configured for "heating only" or "Cooling only", changeover is

not available (see parameter P01)

•

To select cooling or heating manually (P01=2), press the operating mode button

until the

symbol points to the mode you desire.

•

With automatic changeover or continuous heating / cooling, symbols

indicate that the system currently heats or cools.

•

With manual changeover, symbols indicate that the system currently

operates in heating or cooling mode. Symbols

indicate that the system

currently heats or cools.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens RDG100KN Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens RDG100KN

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info