Bedienungsanleitung Siemens RDG110 (Seite 49 von 60) (Englisch)

459668

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

49 / 60

Siemens RDG100, RDG100T, RDG110, RDG140, RDG160 Basic Documentation CE1P3181en

Building Technologies Handling 19 Jun 2009

5 Handling

5.1 Mounting and installation

Do not mount on a wall in niches or book-

shelves, behind curtains, above or near

heat sources, or exposed to direct solar

radiation. Mount about 1.5 m above the

floor.

• The room thermostat must be mounted in a clean, dry indoor place and must not be

exposed to drip or splash water

See Mounting Instructions (M3181) enclosed with the thermostat.

• Comply with local regulations to wire, fuse and earth the thermostat

• Size correctly the cables to the thermostat, fan and valve actuators for AC 230 V

mains voltage

• Use only valve actuators rated for AC 230 V on RDG100… / RDG110

• The power supply line must have an external fuse or circuit breaker with a rated

current of no more than 10 A

• Isolate the cables of inputs X1-M / X2-M and D1-GND if the conduit box carries

AC 230 V mains voltage

• On the RDG100.. and RDG110, inputs X1-M and X2-M carry mains potential.

If the sensor’s cables are extended, they must be suited for mains voltage

• Inputs X1-M, X2-M or D1-GND of different units (e.g. summer / winter switch)

may be connected in parallel with an external switch. Consider overall maximum

contact sensing current for switch rating

• Disconnect power supply before removing the thermostat from the mounting

plate!

Select the application and the type of control output via the DIP switches before

fitting the thermostat to the mounting plate.

After power is applied, the thermostat carries out a reset during which all LCD

segments blink, indicating that the reset was correct. After the reset, which takes

about 3 seconds, the thermostat is ready for commissioning by qualified HVAC

staff.

The control parameters of the thermostat can be set to ensure optimum

performance of the entire system (see section 4.15, control parameters).

• The control sequence may need to be set via parameter P01 depending on the

application. The factory setting for the 2-pipe application is “Cooling only”; and

“Heating and cooling” for the 4-pipe application

• When the thermostat is used in connection with a compressor, the minimum

output on-time (parameter P48) and off-time (parameter P49) for Y11/Y21 must

be adjusted to avoid damage to the compressor and shortening its life

• Recalibrate the temperature sensor if the room temperature displayed on the

thermostat does not match the room temperature measured. To do this, change

parameter P05

• We recommend to review the setpoints and setpoint setting ranges (parameters

P08…P12) and change them as needed to achieve maximum comfort and save

energy

Mounting

Wiring

Commissioning

Control sequence

Compressor-based

application

Calibrate sensor

Setpoint and setpoint

setting range limitation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens RDG110 Seite 49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens RDG110

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info