Bedienungsanleitung Siemens RDG400KN (Seite 1 von 2) (Englisch)

555881

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Operating Instructions

RDG400KN

RDG400KN – the room thermostat with KNX communications that allows you to set the ideal room

temperature you want. The thermostat provides Comfort, Economy and Protection mode.

In addition it can operate in Auto timer mode according to a schedule via KNX bus.

You can either rely on the factory settings or make adjustments that suit your individual needs.

Main display Operating mode

Room temperature

Heating mode

Outdoor temperature

Electric heater active

Room temperature in degrees

Celsius

Cooling mode

Room temperature in degrees

Fahrenheit

Comfort mode

Button lock active

Economy mode

Fault indicator *

Auto timer mode

Condensation in the room *

Protection mode:

Protection against frost

Timer function active

Indicator for mode selection

Weekday 1 = Monday

7 = Sunday

Fan is active **

Additional user info, e.g.

current time of day

Escape (Cancel)

Confirm (OK)

Operating mode button

Protection / OK

Rotary knob

* Needs to be configured by your HVAC installer

** Only supported with Synco 700 primary controller

Changing the room temperature

 Turn the rotary knob clockwise (+) to increase, or counterclockwise (-) to decrease

the current room temperature setpoint. The thermostat changes to Comfort

The setting range is from 5...40 °C; it can be limited by parameters P09 and P10.

(for parameter settings, see reverse side).

Changing the operating mode of the thermostat

Press the operating mode button repeatedly until the

symbol points to the operating

mode you desire.

1. Protection mode

 In protection mode, the plant stops operating. However, if the room temperature

falls below 8 °C, heating is switched on to protect the room against frost.

The setpoints for Protection mode can be changed by your HVAC installer if desired:

Changes made by installer:  Frost protection: _________ ˚C Heat protection: __________˚C

2. Comfort mode

 In Comfort mode, the thermostat maintains

the room temperature on the setpoint

which can be adjusted with the rotary knob

3. Auto Timer mode

 In Auto Timer mode, the thermostat automatically switches over between Comfort

and Economy mode according to the schedule via KNX bus.

If no schedule via KNX is available, then Auto Timer is replaced by Comfort.

4. Economy mode

 In Economy mode, the thermostat maintains the room temperature at a lower or

higher setpoint, thus saving energy and money.

 The thermostat can be set to Economy mode either by pressing the operating

mode button if enabled (P02 = 2), or via an external signal (switch or KNX bus

command) such as window switch, key card or presence detector.

 The Economy setpoints are factory-set to 15 °C for heating and 30 °C for cooling.

They can be adjusted via parameters P11 and P12 (for parameter settings, see

reverse side).

Important: These setpoints can be set to OFF; which means that the thermostat

is not active., i.e. no protective heating or cooling function. Risk of frost!

Changing from heating to cooling mode Not supported with all configurations

 The changeover from heating to cooling (or vice versa) is made

– either automatically by a changeover sensor, or a changeover switch, or a

remote changeover switch via KNX command

– or manually by pressing the operating mode button.

If the thermostat is configured for "heating only" or "Cooling only", changeover is

not available (see parameter P01)

 To select cooling or heating manually (P01=2), press the operating mode button

until the

symbol points to the mode you desire.

 With automatic changeover or continuous heating / cooling, symbols

indicate that the system currently heats or cools.

 With manual changeover, symbols

/ indicate that the system currently

operates in heating or cooling mode. Symbols

indicate that the system

currently heats or cools.

Fan display

The

symbol informs you that the primary fan is active.

Note: Only supported with Synco 700 primary controller.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens RDG400KN Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens RDG400KN

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info