Bedienungsanleitung Siemens RDU341 (Seite 2 von 2) (Englisch)

620392

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

CE1B3172en / 26 Nov 2009 Subject to change Siemens Building Technologies

Temporary timer to extend the Comfort mode

When Energy Saving operating mode is active, press operating mode button

to temporarily return to Comfort mode.

symbol appears. Press opera-

ting mode button

again to stop the timer.

You can only extend Comfort mode if parameter P02 = 1.

Duration * : P68 = 0...360 min, factory setting = 0 min.

Button lock

Press operating mode button

for 5 seconds to lock or unlock the buttons if

manual button lock is configured (parameter P14 = 2).

The thermostat automatically locks the buttons 20 seconds after the last

adjustment if "Auto lock" is configured (P14 = 1).

The key symbol

indicates locked buttons.

External faults

* Needs to be configured by your HVAC installer

Commissioning

You can adjust a number of different control parameters to adapt the thermostat to your system and optimize control perfor-

mance. You can do this during operation either via the buttons on the thermostat or using a commissioning tool.

Control parameters

Proceed as follows to change the most important control parameters:

(Your HVAC installer can set additional parameters)

+ / –

1. Press the – and + buttons simultaneously at least 3 seconds.

Release, and within 2 seconds, press + again for 3 seconds. "P01" is displayed.

2. Repeatedly press the + or – button to select the required parameter.

P01 P02 P08 P14

+-+

3171z99

End

P13

3. Press + and – simultaneously. The current value of the selected parameter begins to flash, allowing you to change

the value by repeatedly pressing + or –.

4. The next parameter is displayed when you press + and – again simultaneously.

5. Repeat steps 2 to 4 to display and change additional parameters,.

6. Press + or – until “End” is displayed, and then press + and – simultaneously to save the change and exit parameter

entry mode.

Para-

meter

Description

Factory setting Setting range Adj 

P01 Control sequence

1 (Cooling only)

0 = Heating only

1 = Cooling only

2 = Manual H or C

3 = Auto Changeover

P02

Mode selection by user via operating mode button

** Without time schedule via KNX, Auto is equal to

Comfort.

1 (Auto **,

Protection)

1 = Auto **, Protection

2 = Auto **, Comfort, Energy

Saving, Protection

P04 Selection of °C or °F °C 0 = °C

1 = °F

P05 Sensor calibration 0.0 °C – 3 ... +3 °C

P06 Standard temperature display 0 (Room temp.) 0 = Room temperature

1 = Setpoint

P07 Additional user information 0 (no display) 0 = No display

1 = Temp. in °C / °F

2 = Outside temperature (via

bus)

3 = Time of day (12h, via bus)

4 = Time of day (24h, via bus)

P08 Comfort basic setpoint 21 °C 5 ... 40 °C

P09 Minimum setpoint limitation in Comfort (WminComf) 5 °C 5 ... 40 °C

P10 Maximum setpoint limitation in Comfort (WmaxComf) 35 °C 5 ... 40 °C

P11 Setpoint of heating in Energy Saving (WheatEco) 15 °C OFF, 5 °C…WcoolEco

P12 Setpoint of cooling in Energy Saving (WcoolEco) 30 °C OFF, WheatEco…40°C

P14 Button lock

(Press operating mode button for 5 seconds to lock or unlock

the buttons)

0 (Disabled) 0 = Disabled

1 = Auto lock

2 = Manual lock

All temperature settings can be made in increments of 0.5 °C.

 Please record all changes you make!

AL1 *

AL2 *

These messages inform you on external faults *:

AL1 : ...……………………… AL2 : ...………………………………….

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens RDU341 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens RDU341

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info