Bedienungsanleitung Siemens RDX33 (Seite 2 von 2) (Englisch)

620393

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

CE1B3075en / 31.10.2008 Subject to alteration Building Technologies

Do you want to reload the default timer settings?

Set the controller to protection mode .

2. Press and simultaneously for 3 seconds. Release them and, within 2

seconds, press 2 times

Day/s

Time when controller is in normal operation

Mo (1) – Fr (5) 06:30 – 08:30 (A1) 17:30 – 22:30 (A2)

Sa (6) 08:00 – 23:00 (A3)

Su (7) 08:00 – 22:30 (A4)

Default

settings

- in the remaining time controller is in energy saving

- timer A5…A8 are free, no default setting

Changing the control parameters

To optimize the control performance, a number of control parameters can be adjusted. This can

also be made during operation without opening the controller.

If you want to change the control parameters, proceed as follows:

(For factory settings, see table on the right-hand side)

1. Set the controller to protection mode

2. Press

and simultaneously for a minimum of 3 and a

maximum of 5 seconds. Release them and, within 2 seconds, press

the

again for 3 seconds. The display will show “P01”.

3. Select the required parameter by repeatedly pressing the

or button:

P01 P02

P18

3075Z03

4. By pressing

and simultaneously, or by pressing , the current

value of the selected parameter appears, which can be changed by repeatedly

pressing

or .

5. 5 seconds after the last press of a button, or by pressing

and

simultaneously, the value will be stored.

6. If you wish to display and change additional parameters,

repeat steps 3 through 5.

7. 10 seconds after the last display or setting, all changes are

stored and the controller will return to standby.

8. Switch to comfort operation with the button.

Changing the batteries

1. Get 2 new batteries of type AA alkaline, 1.5 volts.

2. Within 1 minute: Remove the battery holder, then the batteries, insert new batteries and replace the battery holder.

3. Make certain the old batteries are disposed of properly, in compliance with environmental requirements.

Recalibrating the sensor

If the room temperature displayed by the controller does not agree with the temperature effectively measured, the temperature sensor can be

recalibrated. For that purpose parameter P07 must be changed.

Proceed as described under “Changing the control parameters” and follow steps 1 through 3 to select parameter P07.

With step 4, the room temperature displayed can now be matched to the temperature effectively measured. Each push of the

button changes the temperature by + or – 0.5 °C up to a maximum of + / - 3 °C. With step 7, the recalibration is automatically stored 10

seconds after the last readjustment.

Commissioning (by qualified HVAC staff) (all temperature settings can be made in increments of 0.5 K and the time in increments of 1 min.)

Para-

meter

Controller’s parameter factory settings: Setting range , step RDX33 RDX43

P01 Setpoint of heating in energy saving mode (W heat

Eco

) 16 OFF, 5 °C…W cool

Eco

, 0.5 K

P02 Setpoint of cooling in energy saving mode (W cool

Eco

) 28 OFF, W heat

Eco

…40 °C, 0.5 K

P03*

Setpoint of heating in protection mode

(W heat

PROT

)

8 °C OFF, 5 °C…W cool

PROT

0.5 K

P04*

Setpoint of cooling in protection mode

(W cool

PROT

)

OFF OFF, W heat

PROT

…40 °C, 0.5 K

P05

Min. setpoint limitation in Comfort mode

(W min

Comf.

)

5 °C 5…40 °C, 0.5 K

P06

Max. setpoint limitation in Comfort mode

(W max

Comf.

)

35 °C 5…40 °C, 0.5 K

P07 Sensor calibration 0 K -3…+3 K, 0.5 K

P08 Switching differential heating SDH 2 K 0.5…+4K, 0.5 K

P09 Switching differential cooling SDC 1 K 0.5…+4K, 0.5 K

P10 Setpoint differential between heating & auxiliary heating W

2 K 0.5…+5K, 0.5 K X

P11 Minimum compressor on-time (Q14) 1 min. 1…10 minutes, 1 min.

P12 Minimum compressor off-time (Q14) 3 min. 1…10 minutes, 1 min.

P13 Auxiliary heater minimum hold-time 1 min. 1…10 minutes, 1 min. X

P14 Selection of °C or °F °C

C or °F

P15 Display of temperature or setpoint ON

OFF: Setpoint

ON: Room temperature

P16 Auxiliary heater in heating mode 1: Enable

0: Disable

1: Enable

P17 Time format option 1: 24 h

0: 12 hour format

1: 24 hour format

P18 Operating action changeover heating/cooling Q21 - Q22 0:

0: Open (heating), close

(cooling)

1: Close (heating), open

(cooling)

Legend to table

Adjustable: Please record all changes you make

Not adjustable / display only

Not available

P03* / P04*: P04 is at least min. 5 K higher than P03

Energy saving tips without sacrificing comfort

●

Never allow room temperatures to exceed 21˚C.

● Air out rooms for short periods of time only, but properly, with the windows wide open.

Do you want to view the programmable timer settings?

Press the button to sequentially review the 8 auto timers.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens RDX33 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens RDX33

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info