Bedienungsanleitung Siemens REV100 (Seite 4 von 8) (Englisch)

41505

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

4/8

Siemens Building Technologies Room temperature controller REV100 CE1N2211en

Landis & Staefa Division 16.05.2000

Select the economy temperature and press the time button, then enter the num-

ber of days you are absent

(max. 99 days). The display will show the num-

ber of days and the holiday symbol. Every midnight, the counter subtracts one day.

When the day counter reaches 00, the 24-hour operation with two heating phases will

automatically be resumed.

Press the day counter and set it to 00.

If the temperature displayed does not agree with the room temperature effectively

measured, the temperature sensor can be re-calibrated. For that purpose, set the DIP

switch for Sensor Alignment to ON and press the DIP switch button.

Press

to bring the flashing room temperature in line with the room temperature

currently measured. The increments for the readjustment are 0.2°C {max. ±2 °C).

When balancing of the sensor is completed, the DIP switch must be reset to OFF.

Before cleaning the display or to prevent tampering, the display buttons can be locked.

Press the button behind the little hole for a short moment (max. 1 second):

ap-

pears and all other displays disappear. The display buttons are now disabled while all

the other functions are fully maintained.

Press the button behind the little hole again (max. 1 second).

Keep the button behind the little hole depressed for at least 3 seconds. This resets the

individual settings and the time of day to their default values. During the reset time of 3

seconds, the display will be fully lit, allowing the proper functioning of the display to be

checked. After each reset, all personal settings such as time of day, weekday, switch-

ing points, temperature setpoints, sensor calibration, etc., must be re-entered.

About three months before the batteries are exhausted, the display shows the battery

symbol

. The other displays disappear, the display buttons are deactivated while

all the other functions are fully maintained. When changing the batteries, the current

data will remain stored for at least one minute.

Using a suitable remote operating unit, the REV100 can be switched to economy mode

. Changeover takes place by closing a SRWHQWLDOIUHHFRQWDFW connected to terminals

T1 and T2. In that case, symbol

appears on the display. When the contact opens,

the selected operating mode will be reactivated.

Operation according to controller setting Continuous economy temperature

2252Z05

2252Z06

Suitable remote operating units: telephone modem, manual switch, window switch,

occupancy detector, control centre, etc.

Enter

Cancel

6HQVRUFDOLEUDWLRQ

/RFNLQJWKHGLVSOD\

Switching on

Switching off

5HVHW

%DWWHU\FKDQJH

5HPRWHFRQWURO

Remote operating units

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens REV100 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens REV100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info