Bedienungsanleitung Siemens REV23.03RF (Seite 10 von 17) (Englisch)

41503

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

10/17

Building Technologies Raumtemperaturregler REV23.03RF CE1N2265en

HVAC Products 22.02.2006

The receiver must be wired with the power supply switched off.

Mains voltage may be switched on again only after the unit is completely

mounted.

• When mounting the unit, the base must first be fitted and wired (L/N = AC 230 V

mains supply, LX/L1 = consumers). Then, engage the unit at the top, swing it down-

ward and secure it with a screw

• For more detailed information, refer to the Installation Instructions supplied with the

unit

For the electrical installation, the local safety regulations must be complied with.

• Remove the battery transit tab: As soon as the battery transit tab is removed, the

unit starts to operate.

• If possible, mount receiver temporarily in a first run (e.g. double coated tape). Doing

that, location of best RF reception can be identified later on. See clause “5 Find lo-

cation of best reception“

• Completely wire and mount REV-R.03/1 temporarily (please also close front cover)

a) Switch on power at REV-R.03/1: LED_1 lights always in red or flashes in red

b) Press the "RESET“ button on REV-R.03/1 for about 4 seconds: The orange LED_2

will flash very fast and briefly (stored address of REV23.03RF will be erased)

c) Press the "SET“ button (set / learn) for about 3 sec. until the orange LED_2 starts

flashing slowly and continuously: Receiver is now in learning mode

d) The receiver stays max. 25 minutes in learning mode. If no learning telegram from

REV23.03RF is received during that period of time, repeat steps b) and c) again

e) Press the ESC button

on REV23.03RF for about 4 seconds. Learning tele-

gram is transmitted

f) If REV-R.03/1 receives learning telegram, the orange LED_2 flashes fast and

briefly

g) If the orange LED_2 is steady on, the relay is energized (= controlled device ON)

h) If the orange LED_2 is dark, the relay is deenergized (= controlled device OFF)

i) Depending on the operating state, REV23.03RF repeats the ON or OFF control

telegram every 3 minutes. With this the relay will be switched ON or OFF according

to control telegram latest after 3 minutes

j) If REV-R.03/1 does not receive any correct control telegram within 60 minutes,

controlled device is being switched off and LED_1 flashes in red

k) In the event of a power failure at the REV-R.03/1, the relay will be deenergized.

Mounting and

installation of receiver

REV-R.03/1

Commissioning

controller/transmitter

REV23.03RF

and receiver

REV-R.03/1

1. Switch on

REV23.03RF

2. Mount REV-R.03/1

temporarily

3. Link REV-R.03/1

with REV23.03RF

Override button and

test telegram

ESC button and

learnin

tele

ram

LED_1 (green / red):

Indication for

- Signal strength

- Receiver linked to

cotroller/transmitter

LED_2 (orange):

Indication for

- Learning mode

- Telegram reception

- Status of relais contact

SET button

RESET button

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens REV23.03RF Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens REV23.03RF

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info