Bedienungsanleitung Siemens REV23RF (Seite 10 von 16) (Englisch)

41501

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

10/16

Siemens Building Technologies Raumtemperaturregler REV23RF CE1N2265en

HVAC Products 20.08.2002

Refer to the Installation Instructions printed on the package.

The receiver must be wired with the power supply switched off.

Mains voltage may be switched on again only after the unit is completely

mounted.

• When mounting the unit, the base must first be fitted and wired (L/N = AC 230 V

mains supply, LX/L1 = consumers). Then, engage the unit at the top, swing it down-

ward and secure it with a screw

• For more detailed information, refer to the Installation Instructions supplied with the

unit

For the electrical installation, the local safety regulations must be complied with.

It is recommended to first commission and switch on the receiver, then the transmitter.

• Switch on mains supply

a) Press the «Reset» button (= delete) for about 3 seconds, LED flashes for about 5

seconds (deleting the stored address)

b) Press «Set» button (= setting / learning) for about 1 second until the LED lights

c) The duration of the receiver’s learning readiness is a maximum of 25 minutes.

If no signal is received from the transmitter during that period of time, repeat

steps b) and c)

d) Mount transmitter and put it into operation

e) When the receiver receives a signal from the transmitter, the LED flashes briefly

f) When the LED is steady on, the relay is energized = controlled device ON

g) When the LED is dark, the relay is deenergized = controlled device OFF

h) In the event of a power failure at the receiver, the relay will automatically be de-

energized.

The transmitter repeats the ON or OFF signal at 20-minute intervals, depending

on the operating state. This means that the relay will be energized / deenergized

again after 20 minutes at the latest. This interval was selected to extend battery

life.

If the REV-R.02/1 receives no signal from the controller / transmitter for 60 minutes, the

relay will drop out so that the controlled device will automatically be switched off.

It is recommended to first commission the receiver and then the transmitter.

• If the reference room is equipped with thermostatic radiator valves, they must be fully

opened

a) Remove the battery transit tab, which prevents inadvertent operation of the unit

during transport and storage. The unit switches on

b) When – immediately after switching on – symbol

or appears on the

display (controlled device ON), the first signal has already been sent to the re-

ceiver and communication has been opened

c) Make the settings according to the Operating Instructions

d) If symbol

or does not appear on the display (controlled device OFF), it

must first be activated for signal transmission

e) Select operating mode

(comfort mode)

f) On menu T, select the setpoint for comfort mode

g) Use the roller selector to adjust the setpoint to 29 °C and confirm by pressing

h) Heating ON symbol

or appears on the display after a maximum of one

minute

i) The first signal transmission to the receiver has taken place

j) After 10 seconds, the transmitter sends another signal

Support

Mounting and installa-

tion of receiver

REV-R.02/1

Commissioning

Receiver

REV-R.02/1

Commissioning

Controller / transmit-

ter REV23RF

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens REV23RF Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens REV23RF

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info