Bedienungsanleitung Siemens RVP211 (Seite 3 von 26) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Finnisch)

555851

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Building Technologies 74 319 0614 0 c 20.05.2008 3/26

Anschlussschaltpläne

Siehe Abbildungen

…

auf Seite 24

Für Kleinspannung Für Netzspannung

Brauchwassertemperaturmessung mit Fühler (nur

Typ RVP211)

Externer Schalter zur Betriebsarten-Umschaltung

Brauchwassertemperaturmessung mit Thermostat

(nur Typ RVP211)

Anschluss Dreipunktstellantrieb, Heizkreispumpe

und (nur Typ RVP211) Brauchwasserladepumpe

Anschluss Brenner (Kesseltemperaturregelung)

Anschluss Zweipunktstellantrieb (Vorlauftempera-

turregelung)

Anschluss Stellantrieb für Brauchwasser-

Umlenkventil (nur Typ RVP211)

A6 Raumgerät

B1 Vorlauf- bzw. Kesseltemperaturfühler

B3 Brauchwassertemperaturfühler (nur Typ RVP211)

B9 Witterungsfühler

E1 Brenner

F1 Temperaturwächter

F2 Sicherheitstemperaturbegrenzer

F3 Brauchwasserthermostat (nur Typ RVP211)

M1 Heizkreispumpe

M3 Brauchwasserladepumpe (nur Typ RVP211)

N1 Regler RVP201/211

S1 Externer Schalter

Y1 Dreipunktstellantrieb

Y2 Zweipunktstellantrieb

Y3 Stellantrieb für Umlenkventil (nur Typ RVP211)

en English

Do not throw these instructions away but keep

them with the controller!

Only the RVP211 provides D.h.w. heating.

Installation

Place of installation

In a dry place, e.g. the boiler room.

Mounting choices:

- In the control panel, on the inner wall or on a top hat

rail (EN 60715)

- On a panel

- In the control panel front

- In the sloping front of a control desk

Permissible ambient temperature: 0…50 °C

Electrical installation

- Local regulations on electrical installations must be complied

with

- Cable tension relief must be assured

- The cables from the controller to the actuator and the pump

carry mains voltage

- The cables to the detectors should not be run parallel to mains

carrying cable (insulation class II to EN 60730!)

Specifications of cable

Maximum permissible cable lengths to the detectors and the

room unit:

Copper cable 0.6 mm dia.: 30 m

Copper cable 0.5 mm

: 50 m

Copper cable 1.0 mm

: 80 m

Copper cable 1.5 mm

: 120 m

Installing and wiring the base

Wall mounting

1. Separate base from the controller.

2. Hold base against the wall. Marking "TOP" must be at the

top!

3. Mark fixing holes on the wall.

4. Drill holes.

5. If required, knock out holes on the base for fitting cable entry

glands.

6. Secure base.

7. Wire up base.

Top hat rail mounting

1. Fit top hat rail.

2. Separate base from the controller.

3. If required, knock out holes on the base for fitting cable entry

glands.

4. Fit base to the rail. Marking "TOP" must be at the top!

5. If required, secure the base (depending on type of top hat rail

used).

6. Wire up base.

Flush panel mounting

- Maximum thickness: 3 mm

- Panel cutout required: 138 × 92 mm

1. Separate base from the controller.

2. If required, knock out holes on the base for fitting cable

entry glands.

3. Insert base in the panel cutout from behind until stop is

reached. Marking "TOP" must be at the top!

4. Push lateral tongues behind the front panel:

Refer to figure

on page 24

Place tongues correctly on the left and on the right. They

must not be inside the cutout!

5. Wire up base. Make sure the cable lengths will be adequate

so that the control panel door can be opened.

Fitting the controller to the base

1. Make sure that position and orientation of the turning levers

are correct, using the fixing screws (illustration shows the lat-

eral wall of the controller casing):

Refer to figure

on page 24

2. Insert controller in the base until stop is reached. Marking

"TOP" must be at the top!

3. Tighten fixing screws gradually

Fitting a time switch

If a time switch is to be fitted (weekly or digital time switch), the

respective opening in the cover must be cut out with a knife.

Readjusting the clock after a power failure

When power returns after a power failure, the clock will be read-

justed. Automatic readjustment can be aborted by briefly setting

the operating mode selector to manual operation

and then

back to the required operating mode, allowing manual adjustment

of the clock.

Commissioning

Plant-specific settings

Setting elements: refer to illustration on page 4.

The coding switches and setting potentiometers for the plant-

specific settings are accessible after removal of the time switch.

- Removing the time switch: pull dial away from the controller.

- Fitting the time switch: insert time switch and push it down

(audible click).

Checking the motorized valve

Check the seat or slipper valve: see if

- it is correctly installed (observe direction of flow indicated on

the valve body)

- the slipper moves in the correct angular range (note position

indicator)

- the manual level is disengaged

Exercise caution with underfloor and ceiling

heating systems!

The limit thermostat must be correctly set. During the functional

check, the flow temperature may not exceed the maximum per-

missible level (usually 55 °C). If it does, proceed immediately as

follows:

- Either close the seat or slipper valve manually, or

- Switch off the pump, or

- Close the pump isolating valve

Commissioning the controller

1. Check wiring according to the plant connection diagram.

2. Switch on power supply.

3. Check LED for "Override":

Siemens RVP211 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info