Bedienungsanleitung Siemens TS45200 (Seite 18 von 156) (Alle Sprachen)

690258

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

Trouble shooting

Problem Possible causes Solution

The display does not

react when touched.

• Dirt on the display.

• Fingers are too cold.

• Clean the display with a damp cotton

cloth (not too wet).

• Warm your ﬁngers a little bit and try

again.

“

” icon ﬂashes The steam release button (13)

on the iron handle has not been

pressed during the last 8 minutes,

and the auto shut-off system has

been activated.

Press the steam release button again to

switch the steam station back on.

icon ﬂashes.

Water tank is empty. Fill the water tank.

“

” icon ﬂashes.

Boiler and ﬁlter must be rinsed. Rinse the ﬁlter and the boiler according

to the cleaning instructions in this manual

(see section F).

When touching the

display, the beep cannot

be heard.

The beep has been deactivated. Activate it according to instructions in this

manual. (6. Beep activation/deactivation)

The steam generator

does not come on.

• There is a connection problem.

• The main power button is not

switched on.

• Check the mains cable (5), the plug

and the socket.

• Set the main power button (9) to the “I”

position (illuminated in red).

The iron does not heat

up.

• The main power button is not

switched on.

• The temperature is set to a low

position.

• Set the main power button (9) to the “I”

position (illuminated in red).

• Set the temperature to the desired

position.

The iron begins to smoke

when switched on.

• During ﬁrst use: certain

components on the appliance

have been lightly greased at the

factory and may produce a little

smoke when initially heated.

• During subsequent use: the

soleplate may be soiled.

• This is completely normal and will stop

after a short while.

• Clean the soleplate according to the

cleaning instructions in this manual.

Water ﬂows through the

holes on the soleplate.

• The steam function is being used

before it has reached the correct

temperature.

• The water is condensing inside

the pipes because steam is being

used for the ﬁrst time or has not

been used for a long time.

• Reduce the steam ﬂow when ironing at

low temperatures.

• Point the iron away from the ironing

area and press the steam release

button until steam is produced.

Tips to help you save energy

Steam production consumes the most energy. To help

minimise the energy used, follow the advice below:

• Start by ironing the fabrics that require the lowest

ironing temperature.

Check the recommended ironing temperature in the

label on the garment.

• Regulate the steam according to the selected

ironing temperature, following the instructions in this

manual.

• Try to Iron the fabrics while they are still damp and

reduce the steam setting. Steam will be generated

from the fabrics rather than the iron. If you tumble dry

your fabrics before ironing them, set the tumble drier

on the ‘iron dry’ programme.

• If the fabrics are damp enough, turn off the steam

regulator completely.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens TS45200 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info