Bedienungsanleitung Siemens VS08G1668 (Seite 13 von 138) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

473236

Zoom out

Zoom in

Vorherige Seite

1/138

Nächste Seite

Changing the dust bag and filters

Replacing the MEGAfilt

SuperTEX dust bag

Figure

Ⅲ

If the dust bag change indicator lights up brightly and

evenly when the floor tool is lifted from the carpet and

the highest suction power is selected, the dust bag must

be changed, even though it may not yet be full. In this

case it is essential to change the dust bag due to the

type of material it contains.

Ⅲ

Open the dust bag compartment lid by moving the dust

compartment locking lever in the direction of the arrow.

Figure

Seal the MEGAfilt

SuperTEX dust bag by pulling the self-

seal tap and then remove it.

Figure

Insert a new MEGAfilt

SuperTEX dust bag into the holder

and close the dust bag compartment lid.

Caution: the dust bag compartment lid will

only close

when the MEGAfilt

SuperTEX disposable or textile

filter are inserted.

If the dust bag change indicator is still lit after the

dust bag has been changed, please check whether

the nozzle, tube or flexible hose are blocked.

Cleaning the motor protection filter

The motor protection filter should be cleaned regularly by

knocking out the dirt and rinsing.

Figure

Ⅲ

Open the dust bag compartment lid

(see Figure 16).

Ⅲ

Pull out the motor protection filter in the direction of the

arrow.

Ⅲ

Clean the motor protection filter by

tapping it.

Ⅲ

If it is very dirty, the motor protection filter should be

rinsed.

The filter must then be left to dry for at least 24 hours.

Ⅲ

After cleaning, insert the motor protection filter into the

appliance as far as it will go and close the dust bag

compartment lid.

You can obtain a new motor protection filter on request as

a spare part from the after-sales service. (see Spare parts,

page 13 )

c) Hard furnishings brush

For window frames, cabinets, profiles etc.

Ⅲ

Fold the upholstery nozzle over in the direction of the

arrow.

Ⅲ

To extend the brush ring, turn in the direction of the

arrow.

Before replacing the 4 in 1 tool in the tool holder,

retract the brush ring and fold the upholstery nozzle

back.

Figure

Hard-floor brush

For vacuuming hard floor coverings (tiles, parquet floor-

ing, etc.)

Push the telescopic tube into the connecting piece of

the hard-floor brush until it engages.

Press on the unlatching sleeve and pull out the telescop-

ic tube to disconnect.

Figure

You can use the parking aid on the back of the vacuum

cleaner if you wish to stop vacuuming for a short time.

Slide the plastic lug on the tool connector into the

groove at the back of the vacuum cleaner.

When the work is done

Figure

Ⅲ

Switch the vacuum cleaner off and unplug the power

cord from the mains.

Ⅲ

Tug the power cord and let go. The cable then rewinds

automatically.

Ⅲ

To reactivate or deactivate the cable brake, quickly tug

the power cord.

Figure

To store or transport the vacuum cleaner, use the storage

aid on the underside of the vacuum cleaner. Stand the

vacuum cleaner up on its end. Slide the plastic lug on the

floor tool into the groove on the underside of the unit.

12*

Dependent on model

Innenteil 358 920 A 18.03.2008 15:10 Uhr Seite 11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens VS08G1668 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info