Bedienungsanleitung Siemens VSC3 (Seite 38 von 83) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Portugiesisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

710487

Zoom out

Zoom in

Vorherige Seite

1/83

Nächste Seite

Figure

Set the adjustable ﬂoor tool:

Rugs and carpets =>

Hard ﬂoors =>

If you are vacuuming up relatively large particles, make

sure that you vacuum them up successively and

carefully to ensure that the vacuum channel of the ﬂoor

tool does not become blocked. If necessary, you should

raise the nozzle in order to better vacuum up the dirt

particles.

Figure Vacuuming with accessories

Attach the nozzles to the suction pipe or hand grip as

required:

a)Crevice nozzle for vacuuming crevices and corners,

etc.

b)Upholstery nozzle for vacuuming upholstered

furniture, curtains, etc.

Toy trap*

The toy trap can prevent small parts from being

vacuumed into the dust bag.

Figure

a)Remove the handle from the telescopic tube. Fit the

toy trap between the handle and the suction pipe.

b)Turning the wheel anti-clockwise as far as possible

activates the collection function – small parts are

retained in the collection container.

Turning the wheel clockwise deactivates the

collection function.

c)To remove the small parts that have been collected,

unlock the front window and fold it down.

● Once you have removed the small parts, close and

lock the front window (you should hear it click into

place).

● If necessary, any dirt that has collected can easily be

vacuumed off using the handle.

● Remove the toy trap after use.

!Please note:

The toy trap is not intended for continuous use and

should only be ﬁtted when necessary.

Drill dust nozzle*

Figure

a)Secure the drill dust nozzle to the handle and then

place against the wall, so that the nozzle drill hole

opening sits directly over the hole to be drilled.

b)Select the lowest power setting and then switch on

the vacuum cleaner.

Suction holds the drill dust nozzle in the required

position.

c)Depending on the surface of the wall to be drilled it

may be necessary to readjust the power to a higher

setting to ensure the drill dust nozzle is ﬁrmly

attached.

Any ﬁne particles are automatically vacuumed up.

13*

14*

15*

Figure

You can use the parking aid on the back of the vacuum

cleaner if you wish to stop vacuuming for a short time.

● Once you have switched off the appliance, slide the

hook on the ﬂoor tool into the recess on the rear of

the appliance.

Figure

To overcome obstacles, e.g. steps, the appliance can

also be carried by the handle on the appliance body.

When the work is done

Figure

a)Pull out the mains plug.

b)Brieﬂy pull on the power cord and then release it (the

power cord retracts automatically).

Figure

To store/transport the appliance, you can use the

storage aid on the underside of the appliance.

a)Stand the appliance upright on its end.

b)Slide the hook on the ﬂoor tool into the recess on the

underside of the appliance.

Changing the ﬁlter

Please note: Always switch off the appliance before

changing the ﬁlter.

Replacing the dust bag

Figure

● If the dust bag change indicator in the lid is ﬁlled

completely when the ﬂoor tool is lifted from the ﬂoor

with the highest suction level selected, the dust bag

must be changed, even though it may not yet be full.

Even if the dust bag is not full, it may still need

changing, due to the type of dust which has been

vacuumed. First check that the nozzle, suction pipe

and ﬂexible hose are not blocked, as this would also

lead to the dust bag change indicator being triggered.

● The hand grip can easily be detached from the hose

to remove blockages.

Figure Opening the lid

a)Unlock the lid by pulling on the locking lever in the

direction of the arrow.

b)Open the lid in the direction of the arrow.

Figure

a)Close the dust bag by pulling on the locking tab.

b)Take out the dust bag.

c)Insert a new dust bag.

d)Push the dust bag fully into the holder.

Please note: the lid will only close if a dust bag has

been inserted.

Cleaning the motor protection filter

The motor protection ﬁlter should be cleaned regularly

by knocking out the dirt and rinsing.

20*

depending on model

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens VSC3 Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info