Bedienungsanleitung Siemens VSZ4G2222 (Seite 73 von 136) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

529747

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

Figure Controlling the suction level

The suction level can be inﬁnitely adjusted to the level

required by turning the control knob in the direction of

the arrow.

ow power range =>

or vacuuming delicate materials,e.g.

upholstery, curtains, etc.

Medium power range =>

For the daily vacuuming of light

dirt deposits.

High power range =>

or vacuuming durable ﬂoor coverings,

hard ﬂoors and heavily soiled surfaces.

Vacuuming

Please note:

Floor tools are subject to a certain amount of wear,

epending on the type of hard ﬂoor you have (e.g.

rough, rustic tiles). Therefore, you must check the

underside of the ﬂoor tool at regular intervals. Worn

undersides of ﬂoor tools may have sharp edges that

can damage sensitive hard ﬂoors, such as parquet or

linoleum. The manufacturer does not accept any

responsibility for damage caused by worn ﬂoor tools.

Figure

Set the adjustable ﬂoor tool:

Rugs and carpets =>

Hard ﬂoors =>

If you are vacuuming up relatively large particles, make

sure that you vacuum them up successively and

carefully to ensure that the vacuum channel of the ﬂoor

tool does not become blocked. If necessary, you should

raise the nozzle in order to better vacuum up the dirt

particles.

Figure Vacuuming with accessories

Attach the nozzles to the suction pipe or hand grip as

required:

a)Crevice nozzle for vacuuming crevices and corners,

etc.

b)Upholstery nozzle for vacuuming upholstered

furniture, curtains, etc.

c)Hard-ﬂoor tool

For vacuuming hard ﬂoor coverings

(tiles, parquet ﬂooring, etc.)

● Push the telescopic tube into the connecting piece of

the hard ﬂoor tool until it locks in place.

● To release the connection, press the locking collar

and pull out the telescopic tube.

Figure Cleaning the hard-ﬂoor tool

a)Vacuum the tool from below to clean it.

b)Use scissors to cut through threads and hairs wound

round the rollers and then vacuum them away.

11*

12*

rill dust nozzle

Figure

a)Secure the drill dust nozzle to the handle and then

place against the wall, so that the nozzle drill hole

opening sits directly over the hole to be drilled.

b)Select the lowest power setting and then switch on

he vacuum cleaner.

 Suction holds the drill dust nozzle in the required

position.

c)Depending on the surface of the wall to be drilled it

ay be necessary to readjust the power to a higher

setting to ensure the drill dust nozzle is ﬁrmly

attached.

 Any ﬁne particles are automatically vacuumed up.

Turbo brush

If your appliance is equipped with a turbo brush,

onsult the accompanying instruction manual for

instructions on its use and maintenance.

Figure

You can use the parking aid on the back of the vacuum

cleaner if you wish to stop vacuuming for a short time.

● Once you have switched off the appliance, slide the

hook on the ﬂoor tool into the recess on the rear of

the appliance.

Figure

To overcome obstacles, e.g. steps, the appliance can

also be carried by the handle on the appliance body.

When the work is done

Figure

a)Pull out the mains plug.

b)Brieﬂy pull on the power cord and then release it (the

power cord retracts automatically).

Figure

To store/transport the appliance, you can use the

storage aid on the underside of the appliance.

a)Stand the appliance upright on its end.

b)Slide the hook on the ﬂoor tool into the recess on the

underside of the appliance.

Changing the ﬁlter

Please note: Always switch off the appliance before

changing the ﬁlter.

Replacing the dust bag

Figure

● If the dust bag change indicator in the lid is ﬁlled

completely yellow when the ﬂoor tool is lifted from

the ﬂoor with the highest power setting selected, the

dust bag must be changed, even though it may not

yet be full. Even if the dust bag is not full, it may still

need changing, due to the type of dust which has

been vacuumed.

13*

depending on model

GA 9000 849 148_Z 41 11.12.2012 13:45 Seite 72

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens VSZ4G2222 Seite 73

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info