11
What to do if...
ʑ
Water is leaking out – Attach/replace the drainage hose correctly.
– Tighten the screw connection of the supply hose.
ʑ
No water supply.
Detergent not dispensed.
– (Start/Reload) not selected?
– Tap not turned on?
– Filter blocked? Clean the filter apage 10.
– Supply hose kinked or trapped?
ʑ
The appliance door will not
open.
– Safety function active. Programme stopped? apage 4.
– (without final spin) selected? apage 3, 4.
– Can be opened by emergency release only? apage 9.
– Door locked after the washing machine is switched off: Switch on the washing
machine and wait for 5 seconds.
ʑ
The selected programme does
not start.
– (Start/Reload)or (Ready in) time selected?
– Washing machine door closed?
– Childproof lock active? Deactivate apage 5.
ʑ
Detergent solution is not
drained.
– (without final spin) selected? apage 3, 4.
– Clean the detergent solution pump apage 10.
– Clean the waste pipe and/or drainage hose.
ʑ
No water can be seen in the
drum.
– Not a fault. Water remains inside below the visible area.
ʑ
Spin result not satisfactory.
Laundry wet/too damp.
– Not a fault. Spin control system has stopped the spin cycle. Uneven distribution of
laundry.
Distribute large and small items of laundry evenly in the drum.
– menos â(Reduced Ironing) selected? apage 5.
– Selected speed too low? apage 5.
ʑ
Programme duration changes
suddenly during operation.
– Not a fault. The program time can vary according to the distribution of laundry, with
it therefore being possible for the display panel to show adjustments in the
duration.
ʑ
Spin cycle performed several
times.
– Not a fault. The balance control system has detected an imbalance and is
attempting to redress this by repeating the spin.
ʑ
Residual water in the
compartment for care products.
– Not a fault: the action of the care product is not affected.
– Clean the compartment if necessary apage 9.
ʑ
Odour formation in the washing
machine.
– Run programme algodón/algodão (Cottons)90 °C without laundry. Use
standard detergent.
ʑ
Status display 1 flashing.
Appliance has detected a
detergent overload.
– Too much detergent used?
If foam is escaping from the detergent drawer: mix 1 tablespoon of fabric softener
with ½ litre of water and pour into compartment II (not with outdoor or down
fabrics).
– Reduce the detergent dosage for the next wash cycle.
ʑ
Intense noise formation,
vibrations and "wandering"
during the spin cycle.
– Are the appliance feet fixed?
Secure the appliance feet aInstallation instructions.
– Transportation safety devices removed?
Remove transportation safety devices aInstallation instructions.
ʑ
Display panel/indicator lamps
remain turned off while the
machine is working.
– Energy-saving mode apage 5.
– Power cut?
– Fuses triggered? Reset/change the fuse.
– If the fault occurs repeatedly, call customer services.
ʑ
Programme sequence longer
than usual.
– Not a fault. Unbalanced load detection system adjusts imbalance by repeatedly
distributing the laundry.
– Not a fault: foam detection system active; adds an additional rinse cycle.
ʑ
Detergent residues on the
laundry.
– Occasionally, phosphate-free detergents contain water-insoluble residues.
– Select
mü(Rinse)/ccentrifug. adicional c(Spin) or brush out the laundry after
washing.
If you cannot correct a fault yourself or if a repair is necessary:
– Turn the programme selector to
o (Off) and remove the mains plug from the socket.
– Turn off the water supply and call customer services aInstallation instructions.
