Bedienungsanleitung Sigma EF-610 DG SUPER (Seite 22 von 136) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

542995

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

WHEN BUILT-IN FLASH IS USED (SA-7, SA-9 SD14 AND SD15)

1. Press the MODE button to select the mark.

2. Press the SEL button to make the channel indicator blink.

3. Press the + button or – button to set the channel.

4. Press the SEL button to stop the indicator blinking.

5. Place the EF-610 DG SUPER SA-STTL at the desired position.

■ Do not place the flash unit within the picture area.

■ Please be set the flash unit between 0.5m～5m (1.6 ~16ft) from the subject, and set the camera

body between 1m～5m (1.6~16ft) from the subject.

■ Be sure to set the camera’s flash mode to “Wireless Flash Mode”, and set the channel number on

the EF-610 DG SUPER SA-STTL Flash unit to the same channel number as that you set on the

camera. Otherwise, the EF-610 DG SUPER SA-STTL and your camera will not communicate with

each other and the EF-610 DG SUPER SA-STTL will not fire, when you take picture.

6. Pop-up the camera’s built-in flash, and then after both flashes are fully charged, press the shutter

button to take the picture.

■ AF Auxiliary Light on the EF-610 DG SUPER SA-STTL will blink, when the flash unit charged and is

ready to fire.

■ The EF-610 DG SUPER SA-STTL will fire when the built-in flash fires. The camera’s built-in flash is

fired only to control the EF-610 DG SUPER SA-STTL only. The flash lighting of the subject is done

by the EF-610 DG SUPER SA-STTL. The camera will control the flash power level, as a TTL mode

flash, to Obtain correct exposure.

CAMERAS NOT EQUIPPED WITH BUILT-IN FLASH USED (SD10)

For Wireless flash two pieces of EF-610 DG SUPER SA-STTL will be necessary. In this instruction, we

call a flash unit, which is attached to the camera body “Master unit”, and we call a flash unit at a

remote position “Slave unit”.

Master unit Setting

1. Attach the flash unit to the camera.

2. Press the MODE button to select ⁄ mark.

3. Press SEL button, to make the channel indicator blink on the

display.

4. Press + or – button to set the desired channel number.

5. Press the SEL button several times until the display stops

blinking.

Slave unit Setting

6. Press the MODE button to select .

7. Press SEL button, to make the channel indicator blink, on the display.

8. Press + or – button to choose the same channel number

as set on the Master unit.

9. Press the SEL button several times until the indicator stops

blinking.

10. Place the Slave unit at the desired position.

11. Check that both flashes are fully charged.

■ Ready light lamp will light, and the AF Auxiliary lamp will blink to

indicate that the flash is ready for shooting.

12. Adjust the focus on the subject, and take the picture.

■ Master unit fires just for controlling the Slave unit, and does not influence photography.

■ When you set a slave unit at the desired position, you can use mini-stand. This mini-stand has a

screw hole for a tripod.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sigma EF-610 DG SUPER Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info