Bedienungsanleitung Silvercrest IAN 315097 SHBS 500 D3 (Seite 24 von 96) (Deutsch, Englisch, Holländisch, Französisch, Polnisch, Schwedisch)

751715

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

22 GB

• Place a sheet or cape around throat and

neck to prevent cut-off hair from drop-

ping into the collar.

• Comb the hair well.

•Figure A: first, start with a longer cut-

ting length and then, in the course of the

cutting process, use progressively short-

er cutting lengths. Adjust the cutting

length according to the desired hair

length. Press on the rear of the comb at-

tachment1 to adjust it, and read the

cutting lengths by using the marking11

on the side of the comb attachment1.

NOTE: ensure that the comb attachment1

is still firmly attached to the device after ad-

justment.

• Start by cutting the hair in the neck or on

the sides and cut towards the centre of

the head. Then, cut the front section of the

hair towards the centre of the head.

• Hold the device in such a way that the

comb attachment1 lies as flat as possi-

ble on the head. Move the device

through your hair smoothly and in only

one direction so as to avoid catching.

• If possible, cut against direction of hair

growth.

• In order to catch all the hair, move the

device several times through each sec-

tion of the hair.

• Comb the hair repeatedly and well.

• In order to achieve a straight cutting line

for cutting lengths over 20 mm, the de-

vice should be passed through the hair

several times from different directions.

6.3 Thinning hair

Use the thinning function to reduce the vol-

ume of the hair without changing its length.

• Push the slider3 upwards towards the

shaving head10. The thinning function

integrated into the shaving head10 is

extended upwards.

6.4 Cutting hairlines and

beard

WARNING! Risk of injury!

~The points of the shaving head10 are

sharp. Handle with care.

•Figure A: adjust the cutting length ac-

cording to the desired hair length. Press

on the rear of the comb attachment1 to

adjust it, and read the cutting lengths by

using the marking11 on the side of the

comb attachment1. Now, shorten your

beard step-by-step.

NOTE: ensure that the comb attachment1

is still firmly attached to the device after ad-

justment.

• Use the device only with the shaving

head10 and without comb attach-

ment1, to cut hair very short or to cut

beard and hairline. In this way you can

cut hair lengths of 1-2 mm evenly.

• It is only possible to adjust the cutting

length of the comb attachment1 when

the device is switched off.

• The cutting length setting of the comb

attachment1 is only locked when the

device is switched on.

• It is only possible to adjust the cutting

length of the comb attachment1 when

the device is switched off.

• The cutting length setting of the comb

attachment1 is only locked when the

device is switched on.

__315097_Haar und Bartschneider_B8.book Seite 22 Montag, 3. Juni 2019 1:40 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest IAN 315097 SHBS 500 D3 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info