Bedienungsanleitung Silvercrest IAN 315282 SKMD 1000 A1 (Seite 26 von 96) (Deutsch, Englisch, Holländisch, Französisch, Polnisch, Schwedisch)

752609

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

24 GB

8. Cleaning

DANGER! Risk of electric

shock!

Pull out the mains plug|

from the wall sock-

et before cleaning the coffee machine|

~The coffee machine|6 and the power

cable with the mains plug|7 must not be

immersed in water or other liquids.

DANGER! Risk of injury

through scalding!

The coffee machine|

becomes very hot

during operation. Allow it to cool down

before cleaning.

WARNING! Risk of material damage!

~Do not use any astringent or abrasive

cleaning agents.

NOTE: in order to start the brewing process

with clear water or a descaling solution, the

filling of the water tank|4 must not exceed

the 8 cup marking. Otherwise, the ther-

mal jug|8 may overflow.

8.1 After every use

Clean the device after every use, if possible.

1. Disconnect the mains plug|7 from the

wall socket.

2. Open the lid|1.

3. Lift up the handle|12 of the filter hold-

er|11, remove the filter holder and dis-

pose of the used paper filter.

4. Rinse out the filter holder|11 with warm

water.

5. Rinse out or off the thermal jug|8 and its

lid|9 with clear water. Only in the case

of stubborn residues, you should use a

little mild detergent and a rinsing brush

which is not too hard. Then rinse all

parts thoroughly with clear water.

6. Wipe down the coffee machine|6 and

the power cable|7with a damp cloth

when required. Dry with a dry cloth.

7. Allow all parts to dry completely before you

put them away or use the device again.

NOTE: the thermal jug|8 can also be

cleaned on the outside with stainless steel

cleaners from specialist retailers.

8.2 Descaling

Time intervals for descaling

The intervals for descaling are dependent

on the hardness of the water, and how often

you use the device. Where the hardness of

the water is medium or high, we recommend

descaling monthly.

If using tap water, you can find out the hard-

ness of the water in the area where you live

by inquiring at your local waterworks.

After some time, the boiling process will re-

sult in limescale being deposited in parts of

the coffee machine (depending on the hard-

ness of the water used). You should remove

this at regular intervals, because otherwise

the power consumption of the device will in-

crease.

1. Turn off the coffee machine|6 and allow

it to cool down completely.

2. Place the descaling agent into the water

tank|4. Use a liquid, environmentally

friendly descaling agent based on citric

acid, and follow the instructions of the

manufacturer.

3. Fill the water tank|4 to the 8 cup

marking.

4. Close the lid|1 of the coffee machine|6.

5. It is very important to screw the

lid|9 on the thermal jug|8.

6. Place the thermal jug|8 in the coffee

machine|6.

7. Press |18. The red LED|19 lights up

and the brewing process will start after

a short time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest IAN 315282 SKMD 1000 A1 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info