Bedienungsanleitung Silvercrest IAN 322112 SHH 1200 D2 (Seite 22 von 81) (Deutsch, Englisch, Holländisch, Französisch, Polnisch, Schwedisch)

751808

Zoom out

Zoom in

Vorherige Seite

1/81

Nächste Seite

GB/IE24

Please note: The unit may produce a slight odour

for a short time when used for the ﬁrst time.

Start up

 Switching on/oﬀ

Make sure that the three heat level switches 2, 3

and 4 are set to “0”. Then connect the heater

to a grounded socket protected by a residual-

current device with overload protection. The heating

unit must be freely rotatable.

Now switch on the unit by switching the on/oﬀ

switch 4 to the “I” position. To turn oﬀ the unit,

switch the on/oﬀ switch 4 to the “0” position.

Please note: When the unit is switched on, the middle

heating element is activated.

 Heating levels

The halogen heating unit has three diﬀerent

heating levels: 400W, 800W and 1200W.

The ﬁrst heating level (400W) is reached when

the unit is switched on. In the process, the central-

heating element is put into operation (see chapter

Switching on/oﬀ).

The second heating level (800W) is reached by

additionally switching one of the heating level

switches to on

(

)

Please note: The heating level switch

switches the

lower heating element on.

The heating level switch

switches the upper heating element on.

The third heating level

(1200W) is reached by

additionally switching both of the heating level switch-

es to on (

 Oscillation

Set the oscillation switch

1 to “I” to activate the

function. The heater fan will begin to move from

side to side.

To disable the oscillation, switch the oscillation

switch

1 to “0”.

 Overheating protection

This unit is equipped with an overheating protection

device. If the unit is too hot, the heating element switches

oﬀ automatically. Turn the unit OFF by turning the

heating level switch to “0” and pull the power plug

out of the socket. Please note: If the overheating pro-

tection is triggered, you should turn OFF the unit and

contact the service hotline (see chapter “Service”).

 Tip-over protection

This unit is equipped with a tip-over protection device.

This is located in the base of the unit. If the unit is

inadvertently knocked over or tilted heavily during

operation, it will switch oﬀ automatically. The unit is

only functional in an upright position.

 Maintenance, Cleaning

and Storage

Always disconnect the power plug when the device

is not in use and before any cleaning or in the

event of operating faults!

Clean the device only when it is turned OFF and

in a cooled condition.

Ensure that no moisture penetrates into the device

in order to avoid irreparable damage.

Clean the housing with a soft dry cloth only.

Do not use aggressive and/or abrasive cleaning

agents.

Remove dust deposits from the protective grille

with a vacuum cleaner.

Store the device in a dry room.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest IAN 322112 SHH 1200 D2 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info