Bedienungsanleitung Silvercrest IAN 337147 LHL 2000 C2 (Seite 10 von 36) (Englisch)

749737

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

GB/IE/NI/CY 11

0Position OFF If the heating level switch

2 is in this position, the

device is turned oﬀ.

Fan position When the heating

level switch 2 is in

this position, only the fan

is running. If you would

like to use the device as

a ventilator, move the

switch to this position.

IHeating

level 1

If the heating level switch

2 is in this position, the

fan heater develops a

heating power of 1000

II Heating

level 2

If the heating level switch

2 is in this position, the

fan heater develops a

heating power of 2000

MIN position of the thermoregulator

MAX position of the thermoregulator

Temperature Setting

▪ Start the device with setting the desired heating

capacity with the aid of the heating level switch

▪ Turn the temperature regulator 4 in a clockwise

direction as far as it will go.

▪ If the desired temperature is not reached, turn

back the temperature regulator 4 coun-

ter-clockwise until you hear a clear click. The

control light 3 goes out. Then an integrated

thermostat controller will automatically turn the

heating function ON or OFF. The fan continues

to run constantly.

Please note: When the thermostat is in the MIN po-

sition, the device remains completely OFF.

 Turning OFF the Device

▪ Set the heating level switch 2 on the "Fan" po-

sition and wait 30 seconds to allow the heating

elements to cool down. Damage to the device

could occur if not observed.

▪ Set the heating level switch 2 at position “0”.

▪Pull the power plug out of the socket.

Before you cover the device or put it away,

wait until it has cooled down.

 Thermal overload protection

This device is equipped with an overheating protection.

If the device is too hot, the heating element switches oﬀ

automatically.

Turn the device OFF by turning the heating level switch

“0”

and pull the power plug out of the sock-

et. Wait until the device has cooled down - at least 10

minutes.

Check the air inlet and air outlet holes. Eliminate the cause

of the overheating before you restart the device.

CAUTION! Usually the device never gets

overheated without cause! If it gets too hot,

there is a danger of ﬁre!

▪ Check whether the device is able to give oﬀ the

heat properly: Is the device covered with any-

thing? Or, perhaps, it is too close to a wall or

other obstacle? Check whether the grids on the

front or rear side are free of dirt and not covered.

Is the fan blocked?

▪

If possible, eliminate the cause of the prob-

lem or contact the service hotline (see chapter

"Service").

▪ Please note: If the overheating protection is trig-

gered for the second time, you should turn OFF

the device and contact the service hotline (see

chapter "Service") - regardless of if you have

found the cause of the problem or not.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest IAN 337147 LHL 2000 C2 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Silvercrest IAN 337147 LHL 2000 C2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info