Bedienungsanleitung Silvercrest IAN 365240 (Seite 43 von 179) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Spanisch, Polnisch)

793044

Zoom out

Zoom in

Vorherige Seite

1/179

Nächste Seite

43 GB/IE

to prevent the accessory parts coming loose

from the accessory holder 10 unintentionally

during operation.

Put the accessory holder 10 back on the alu-

minium suction tube 16 after vacuuming.

Cleaning, care and

maintenance

Emptying the dust collector

To empty the dust collector 21 , it must be removed

from the main unit 4.

First remove the aluminium suction tube 16 or the

accessory part you were using (see chapter “Select-

ing, assembling and disassembling accessories”).

Proceed as follows to empty the dust collector 21 :

Switch the product oﬀ using the On / Oﬀ

button 19 (see Fig. A).

Remove the dust collector 21 from the main

unit 4 by pushing the release button 22 on

the base of the dust collector 21 (see Fig. G)

and carefully removing the dust collector 21 as

shown in ﬁgure H.

Hold the dust collector 21 over a waste bin.

The distance to the dust collector should be as

small as possible so that the dust does not un-

necessarily shake out and distribute itself in the

surrounding area.

Pull the release lever 23 downwards (towards

the user) to open the base ﬂap 21 b on the dust

collector 21 (see Figure I).

If needed, remove hair and dust, which have

become stuck to the dust collector 21 by hand.

Close the base ﬂap 21 b again by pushing it

back into the opening of the dust collector 21

and pushing the release lever 23 upwards

(towards the dust collector 21 ) until it audibly

clicks into place (see Fig. J).

Replace the dust collector 21 on the main unit

4 by lining up the dust collector 21 and the

cover 24 precisely in the corresponding recesses

in the main unit 4 (see Fig. K). The dust col-

lector 21 must audibly click into place, it is

only properly installed if it does so (see Fig. L).

Cleaning the ﬁlters

and dust collector

Clean the ﬁlters (HEPA ﬁlter 25

and stainless steel ﬁlter 27 ) after

every two or three uses. Other-

wise the vacuum function will be

reduced and the product could

be damaged.

Do not wash the ﬁlters (HEPA

ﬁlter 25 and stainless steel ﬁlter

27 ) in the dishwasher or wash-

ing machine.

Do not clean the HEPA ﬁlter 25

under running water.

Do not clean the dust collector

21 in the dishwasher.

Allow the stainless steel ﬁlter 27

to air dry thoroughly after clean-

ing.

Do not put the stainless steel

ﬁlter 27 in the dryer or on the

stove to dry.

IMPORTANT: Allow all parts

of the product to dry thoroughly

after cleaning. If the stainless

steel ﬁlter 27 is not fully dry, wa-

ter may seep into the product

and damage it!

To clean the filters, follow these steps:

Switch the product oﬀ using the On / Oﬀ

button 19 (see Fig. A).

Remove the aluminium suction tube 16 from

the main unit 4 by pushing the upper release

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest IAN 365240 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info