Bedienungsanleitung Silvercrest IAN 64641 (Seite 29 von 40) (Englisch, Portugiesisch, Spanisch)

738619

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

33 GB/MT

Safety system

Note: the heating pad is equipped with a safety

system. The electronic sensor technology prevents the

entire surface of the heating pad from overheating

by automatically switching oﬀ in the event of a fault.

If the safety system switches the heating pad oﬀ

automatically due to a fault, then the function

indicator

on the control unit

ceases to illu-

minate, even if the heating pad is switched on.

j Please note that, for safety reasons, the heating

pad must not be used after a fault and must be

returned to the service address indicated.

Operation

Note: the heating pad may smell of plastic the

ﬁrst time you use it, but this will disappear after a

short period of time.

j Place the heating pad in position as shown in

Fig. C. Join the two ends of the heating pad

together.

j Integrated magnets

ensure that the two

ends of the heating pad remain in contact.

j You can use the snap fasteners

if you wish

a closer ﬁt.

Switching on / oﬀ / Selecting

the temperature

j To begin, ﬁrst connect the control

to the

heating pad with the plug-in connector

(see Fig. B).

Switching on:

j Set Level 1, 2, 3, 4, 5 or 6 on the control

switch the heating pad on.

Note: The function indicator

illuminates after

the heating pad is switched on.

Note: this heating pad features rapid heating,

which allows it to heat up within the ﬁrst 10 minutes

of operation.

Switching oﬀ:

j Set Level 0 on the control

to switch the

heating pad oﬀ.

Note: The function indicator

ceases to illuminate.

Selecting the temperature:

j Just before using the heating pad, set it to the

highest temperature setting (setting 6). This will

cause the heating pad to warm up quickly.

j If you are going to use the heating pad for a

number of hours, set it to the lowest temperature

setting (setting 1).

Temperature levels

j Set the required temperature level on the

control

(see Fig. A).

Level 0: oﬀ

Level 1: minimum heat

Level 2-5: customised settings

Level 6: maximum heat

Automatic switch-oﬀ

Note: The heating pad switches itself oﬀ automati-

cally after about 90 minutes. The function indicator

then starts to ﬂash.

j Then select the setting 0 and after about

5 seconds, reset the heating pad to the desired

temperature setting to switch it on again.

j Switch the heating pad oﬀ (setting 0) and

pull the mains plug out of the mains socket if

the heating pad is not to be used after it has

switched itself oﬀ automatically.

Cleaning and care

WARNING!

DANGER TO

LIFE BY ELECTRIC SHOCK! Al-

ways remove the mains plug from

the socket and the plug-in connector

with

the control

from the heating pad (see Fig. B)

before cleaning the heating pad.

Safety system / Operation / Cleaning and care

64641_silv_Schulterheizkissen_Content_LB5.indd 33 07.04.11 10:36

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest IAN 64641 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Silvercrest IAN 64641

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info