Bedienungsanleitung Silvercrest KH 6518 (Seite 6 von 29) (Englisch)

569510

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

- 6 -

• Never cover the ventilation slots of the device while it is being used.

• Do not place any open sources of fire, like candles, on the device.

Injury hazard

• Keep children away from the connecting cable and the device. Children

frequently underestimate the dangers of electrical devices.

• Ensure that the device stands with a safe and secure positioning.

• Do not operate the device if it has sustained a fall or is damaged. Arrange

for the device to be checked and/or repaired by qualified technicians.

• Keep batteries away from children. Children can put batteries into their

mouths and swallow them.

Danger! Laser radiation!

This device is fitted with a „Class 1 Laser“.

• Never open the device.

• Never attempt to repair the device.

• There is invisible laser radiation inside the device.

Do not expose yourself to the laser beam.

Note:

Some aggressive furniture finishes can have a destructive influence on

the device's rubber feet. If necessary, place the device on a nonslip pad.

Thunderstorms!

Equipment connected to a power supply can be damaged during a

thunderstorm. You should therefore always pull the power plug from

the power socket when there is a storm.

Notice regarding electrical power surges (EFT /

electrical fast transient) and electrostatic discharges:

In a case of malfunction due to an electrical fast transient (power surge)

and/or electrostatic discharge, the device must be returned to default

settings in order to re-establish normal operation. Possibly the power

supply must be separated and then reconnected. The batteries (if pre-

sent) must be removed and then reinserted.

Notice regarding separation from mains-power

The POWER switch does not completely disconnect the device from the

power network. Additionally, the device consumes power when in stand-

by-mode. To completely separate the device from mains-power, the power

plug MUST be removed from the wall socket.

Information regarding the handling of batteries

The remote control is operated by batteries.

For the handling of batteries please observe the following:

Risk of explosion!

Do not throw batteries into a fire. Do not recharge the batteries.

• Never open batteries, never solder or weld batteries.

The risk of explosions and injuries exists!

• Regularly check the condition of the batteries. Leaking batteries can

cause damage to the device.

• If you do not intend to use the device for an extended period, remove

the batteries.

• In the event of the batteries leaking acids, wear protective gloves.

• Clean the battery compartment and the battery contacts with a dry

cloth.

Attention!

No liability/warranty will be considered for damage to the DVD player

caused by the effects of moisture, water penetration or overheating!

7. Remote control

7.1 Inserting the batteries

1. Open the battery compartment on the rear of the remote control.

2. Place the two supplied batteries type AAA (micro cells) into the battery

compartment. Make sure that the batteries are inserted in accordance

with the correct polarity.

3. Replace the battery compartment cover.

7.2 Using the remote control

In order to guarantee faultless operation when using the remote control…

• Always point the remote control, during use, directely at the DVD player

• Make sure that there are no obstructions between the remote control

and the DVD player that will hinder reception.

• When using the remote control place yourself not more than 5 metres

from the DVD player

otherwise interferences can occur during operation of the DVD player functions

with the remote control.

7.3 Replacing the batteries

If the operation of the DVD player via the remote control does not function

properly or does not function at all the batteries must be replaced

• Always renew all batteries in order to return the remote control to its

full performance ability.

8. Connecting the DVD Player to a television

After setting up the DVD player, you can now connect it to a television. The

DVD player can be connected to televisions which operate with the PAL and

NTSC standards.

If you want to use the DVD player on a television with the NTSC standard

you must change the video setting in the DVD players "OSD menu".

There PAL is set as the television standard at the factory.

On this topic see also chapter 10.3. "Video settings: Setting the

TV standard".

Depending on the televisions equipment there are different methods of

connecting the DVD player to it, these are explained as follows.

IB_KH6517_18_DVDPlayer_LB6.qxd 23.01.2008 19:07 Uhr Seite 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest KH 6518 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Silvercrest KH 6518

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info