Bedienungsanleitung Silvercrest KH2380 (Seite 23 von 30) (Englisch)

118060

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

23 GB/IE

L Troubleshooting

 E Error e Cause E Remedy

E The device can not be switched on or the

display

3indicates [ERROR].

The connections for the 12 V DC power supply

are faulty.

E Check that the wiring of the device is correct

(see the section on “Connecting to the Vehicle’s

V DC Power Supply”). Then press the RESET

button

drwith the tip of the ballpoint pen.

The 10 A euﬂat blade fuse in the ﬂat blade fuse

socket

etis broken.

E Replace the broken ﬂa

t blade fuse with a new

10 A ﬂat blade fuse. Then press the RESET

button

drwith the tip of the ballpoint pen.

A 15 A fuse of the fuse holder of the 12 V DC

power supply is broken.

E Replace the broken fuse with a new 1

5 A fuse.

Then press the RESET button

drwith the tip of

the ballpoint pen.

If the fuse is broken again, check that the

wiring is correct.

e The device is broken.

E Please contact the ser

vice centre for your

country (see guarantee card).

E The device cannot be operated.

e The control panel

1is wrongly connected.

E Ensure tha

t the control panel 1is correctly

connected (see the section on attaching the

control panel).

The battery of the remote control is ﬂat.

E Replace the used ba

ttery with a new lithium

battery of type CR2025, 3 V DC.

The sensor coof the control panel 1and / or

remote control may be dirty.

E Clean the sensor

coof the control panel 1or

the remote control if necessary.

e The device is broken.

E Please contact the ser

vice centre for your

country (see guarantee card).

E The stored stations do not remain stored if

the control panel is removed or the engine

turned off.

The connections for 12 V constant current fm

and 12 volt ignition current

fphave been

mixed up on the ISO plug in the vehicle

(various layouts of the respective manufactur-

ers). As soon as the ignition is switched off the

internal memory of the radio no longer has any

power supply.

E The colour coding of the sta

ted cables must be

red and yellow. In this case swap over the

connections for 12

V constant current

fmand

12 volt ignition current

fo. Some manufactur-

ers provide the opportunity of swapping the

two cables by means of preassembled plug-in

connectors. A further possibility is to purchase

an additional ISO adapter (plug on socket) with

plug-in connectors from a specialist shop and

also to swap over the two contacts (red and

yellow).

This work should only be carried out by a

professional electrician.

L Maintenance and Service

• Switch off the device.

The device is maintenance free.

• Clean plastic surfaces of the device and of the

remote control with a dry cloth. Do not use

solvents or other aggressive cleaning agents.

Changing the battery of the remote control

•

Activate the unlock button

isand pull the

battery holder

irfrom the battery compart-

ment

iq(see Fig. G).

• Place a Lithium battery type CR2025, 3 V DC

into the battery holder

irso that one side

marked with “+” faces up. Then slide the

battery holder

irinto the battery compartment

iquntil it distinctly catches.

Troubleshooting / Maintenance and Service

KH2380_Content_UK.indd 23 12.09.2006 11:57:16 Uhr

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest KH2380 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Silvercrest KH2380

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info