Bedienungsanleitung Silvercrest P10F - IAN 66353 (Seite 29 von 40) (Englisch, Portugiesisch, Spanisch)

658893

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

33 GB/MT

Operation / Cleaning and care

Operation

Note: The heating pad may smell of plastic the

ﬁrst time you use it, but this will disappear after a

short period of time.

Position the heating pad on your back so that the

fastener for the neck section is in the throat area.

Only close the fastener when the pad is

positioned properly.

Then adjust the length of the belt around your

stomach and ﬁt the two ends of the connector

together (see Fig. C) to fasten the belt.

To open the belt, press the two catches on the

connector at the same time (see Fig. C).

Switching on / oﬀ / Selecting

the temperature

To begin, ﬁrst connect the control

to the

heating pad with the plug-in connector

(see Fig. B).

Switching on:

Set the control unit

to setting 1, 2, 3, 4, 5

or 6 to switch on the heating pad.

Note: The function indicator

illuminates after

the heating pad is switched on.

Note: This heating pad features rapid heating,

which allows it to heat up within the ﬁrst 10 minutes

of operation.

Switching off:

Set Level 0 on the control

to switch the

heating pad oﬀ.

Note: The function indicator

ceases to illuminate.

Selecting the temperature:

Just before using the heating pad, set it to the

highest temperature level (Level 6). This will

cause the heating pad to warm up quickly.

If you wish to use the heating pad over several

hours, set the lowest temperature level (Level 1).

Temperature levels

Set the required temperature level on the

control

(see Fig. A).

Level 0: oﬀ

Level 1: minimum heat

Level 2–5: customised heat

Level 6: maximum heat

Automatic switch-oﬀ

Note: The heating pad switches itself oﬀ auto-

matically after about 90 minutes. The function

indicator

then starts to ﬂash.

Then select the setting “0” and after about

5 seconds, reset the heating pad to the desired

temperature setting to switch it on again.

Switch the heating pad oﬀ (setting “0”) and

pull the mains plug out of the mains socket if

the heating pad is not to be used after it has

switched itself oﬀ automatically.

Cleaning and care

DANGER

TO LIFE BY ELECTRIC SHOCK!

Always remove the mains plug from

the socket and the plug-in connector

with

the control

from the heating pad (see Fig. B)

before cleaning the heating pad.

DANGER OF ELECTRIC SHOCK!

Do not reconnect the control

the heating pad until the plug-in con-

nector

and the heating pad are completely

dry. There is otherwise a risk of an electric shock.

DANGER OF ELECTRIC SHOCK!

DANGER OF MATERIAL

DAMAGE! Do not under any

circumstances switch the heating pad on to

help it dry.

Use a dry, non-ﬂuﬃng cloth for cleaning and

care of the heating pad and control

66353_silv_Ruecken_Nacken_Heizkissen_Content_LB5.indd 33 17.05.11 13:28

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest P10F - IAN 66353 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Silvercrest P10F - IAN 66353

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info