Bedienungsanleitung Silvercrest SAB4.8A2032012-3 IAN 75164 (Seite 24 von 25) (Deutsch, Englisch, Holländisch, Französisch)

739555

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

- 22 -

Working with the floor sweeper



Caution:

• Never use the device with the dirt container

removed. The dirt would only be swirled around!

• Keep end of rotating brush, wands and other

openings away from your face and body. Risk of

injury!

• Press the switch  to start the rechargeable bat-

tery floor sweeper. Press again to switch off the

device.

• Guide the rechargeable battery floor sweeper

over the floor.

• You can leave the floor sweeperstick locked in

vertical position during work interruptions.



Note:

With some types of carpet the rechargeable battery

floor sweeper could rattle or bounce. In this case

work slowly and in the opposite direction.

Cleaning



Caution:

Do not clean the appliance while charging it. Always

disconnect the battery charger from the mains po-

wer socket before cleaning the appliance!

To clean the housing:

Wipe the housing of the appliance with a damp

cloth. If necessary, use a mild detergent on the

cloth.

Ensure that the appliance is completely dry before

reconnecting it with the battery charger.

How to clean the dirt container:

To maintain the efficiency of the rechargeable

battery floor sweeper, empty the dirt container after

every use.

• Press the unlocking locking release button  of

the dirt container to detach it from the device.

• Remove the dirt container from the appliance

horizontally with a downward movement.

• Empty the dirt container and re-insert.

How to clean the brush:

If the brush roller cannot be turned any longer

because of accumulated coarse dirt or threads,

proceed as follows:

• Turn over the rechargeable battery floor swee-

per and hold it so that the flat side with the brush

roller faces you.

• Remove the small cover  on the right-hand

side.

• Loosen the drive belt by pushing it to the right.

• Lift the brush roller on the right-hand side and

remove the guide attachment  with the washer.

• Now pull the brush roller from the device to the

right-hand side.

• Remove the dirt (on both sides of the bristle) and

clean the brush.

After cleaning, proceed as follows to re-install the

brush roller:

• Insert the drive belt in the compartment and

place it around the motor drive pulley.

• Place the washer on the guide attachment 

and insert the brush roller into the left guide

channel.

• Pull the drive belt over the guide attachment 

and re-insert the brush roller into the right channel.

• Now pull the drive belt over the drive cog of the

brush roller.

• Fit the brush cover  by first introducing the

lower lugs in the recesses and press the cover 

in at the top.



Caution:

• Ensure that the device is not inadvertently

switched on with the dirt container removed or

while cleaning the brush. Risk of Injury!

• Do not clean the device during the charging

process. Risk of Injury!

IB_75164_SAB48A2_LB2.qxp 22.05.2012 12:38 Uhr Seite 22

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest SAB4.8A2032012-3 IAN 75164 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info