Bedienungsanleitung Silvercrest SAS 150 A1 - IAN 46298 (Seite 33 von 45) (Englisch, Portugiesisch, Spanisch)

575513

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

33 GB/MT

Operation

5. The cutting blade

continues to rotate for a

short while after the slicer has been switched oﬀ.

6. For reasons of safety, the slice thickness must

be returned to the „0“ setting after use.

Soft foodstuffs:

˽ Direct the food carriage

slowly against the

cutter

. Soft foodstuﬀs, for example hams or

cheeses, are best cut when they are at a low

temperature / lightly chilled.

Hard foodstuffs:

˽ With hard foodstuﬀs you can direct the food car-

riage

somewhat faster against the cutter

You can thus quickly prepare your required

amount of of sliced foods, for example salami,

bread or gherkins.

Selecting mode of operation

Note:

The two operating modes can be switched on

and oﬀ with the rocker switch for intermittent /

continuous operation

Continuous operation / max. 10 minutes

(switch in position „I“):

˽ Set the switch for intermittent / continuous oper-

ation

to position „I“. The cutting blade

runs without it being necessary to hold the switch

in this position.

Halting continuous operation: Move the switch

for intermittent / continuous operation

into

the „0“ position and wait until the cutting blade

comes to a complete standstill.

Intermittent operation (switch for

intermittent / continuous operation

in position „II“):

˽ Set the switch for intermittent / continuous

operation

to position „II“.The cutting blade

will continue to run for as long as the switch

for intermittent / continuous operation is

held in this position. Halting intermittent opera-

tion: Release the switch for intermittent / contin-

uous operation

and wait until the cutting

blade comes to a complete standstill.

Setting the Vario-switch

cutting blade speed

Low revolutions / Revolution symbol

narrow end:

˽ Set a low revolution speed when you want to

cut soft foodstuﬀs.Push the Vario-switch

completely in the direction of the sharp end.

High revolutions / Revolution symbol

wide end:

˽ Use a high revolution speed for slicing hard

foodstuﬀs. Push the Vario-switch

completely

in the direction of the broad end.

Note: Between the maximum and minimum

adjustments you can naturally also carry out

further individual settings. Practice appropriate

trial slicings.

Slice thickness - setting

and cutting

Set the required slice thickness using the control

knob

(see Figure C). The settings on the scale

do not correspond with the slice thickness in mm.

For safety reasons the cuttingblade

is covered

in setting „0“.

˽ Place the food to be sliced on the food

carriage

If necessary, press the food to be sliced with

the food holder plate

lightly against the

food support

˽ Switch the appliance on and, whilst lightly

pressing the food to be sliced forward, guide

it along the cutting blade

. After using the

slicer always set the food support plate

into

the „0“ setting so that the sharp blade is covered.

The cutting blade

is ideally suitable for cut-

ting wafer-thin slices of cold cuts or boiled ham

(see Fig. A).

˽ To safeguard your ﬁngers always use the food

carriage

and the food holder plate

(Ex-

ception: slicing very large pieces of foodstuﬀs).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest SAS 150 A1 - IAN 46298 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Silvercrest SAS 150 A1 - IAN 46298

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info