Bedienungsanleitung Silvercrest SBB 850 B1 - IAN 274313 (Seite 81 von 90) (Deutsch, Englisch, Französisch, Italienisch)

646204

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

■ 78

│

SBB 850 B1

You can monitor the programme sequence through

the viewing window 1 of your bread maker.

Occasionally, condensation may build up on the

viewing window 1 during baking. The appliance

lid 2 may be opened during the kneading phase.

NOTE

► Do not open the appliance lid 2 during the

rising or baking phases. The br

ead could

collapse.

Ending a programme

When the baking process has been completed,

you will hear ten beeps and the display  indicates

0:00. At the end of the programme, the appliance

automatically changes to a keep-warm mode for

up to 60 minutes.

NOTE

► This does not apply to programmes 6, 7 and

11.

In this mode, w

arm air circulates inside the appli-

ance. The keep-warm function can be ended early

by keeping the Start/Stop button  pressed until

a beep is heard.

DANGER! ELECTRIC SHOCK!

► Before opening the appliance lid 2, discon-

nect the po

wer plug from the socket. The

appliance should always be disconnected

from the power grid when not in use!

Taking out the bread

Always use pot holders or oven gloves when re-

moving the hot baking mould 7. Hold the baking

mould 7 tilted over a grill tray and shake it lightly

until the bread slides out of the baking mould 7.

If you haven't already removed the kneading hooks:

If the bread does not slip oﬀ the kneading blades 6,

carefully remove the kneading blades 6 using the

supplied kneading blade remover 0.

NOTE

Do not use any metal objects that could cause

scr

atches on the non-stick coating. Rinse the

baking mould 7 with warm water directly after

removing the bread. This will help prevent the

kneading blades 6 becoming stuck on the drive

shafts.

■ Press the Start/Stop button  brieﬂ

y to pause

the programme at the very start of the baking

phase or, pull the power plug out of the socket.

Ensure that you replace the power plug within

10 minutes so that the baking process can be

continued.

■ Open the appliance lid 2 and r

emove the

baking mould 7. With ﬂ oured hands, you can

remove the dough and then pull out the knead-

ing blades 6.

■ Replace the dough in the back baking mould 7.

Replace the baking mould 7 and close the

appliance lid 2.

■ Put the power plug into the socket if necessary.

The baking program continues from where it

was stopped.

Allow the bread to cool for 15–30 minutes before

eating it.

Before cutting the bread, always check to ensure

that the kneading blades 6 have been removed

from it.

Error messages

■ If the display  sho

ws "HHH" after the pro-

gramme has been started, it indicates that the

temperature in the bread maker is still too high.

Stop the programme and remove the power

plug. Open the appliance lid 2 and allow the

machine to cool down for 20 minutes before

reusing it.

IB_274313_SBB850B1_CH.indb 78 17.02.16 16:32

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest SBB 850 B1 - IAN 274313 Seite 81

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Silvercrest SBB 850 B1 - IAN 274313

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info