Bedienungsanleitung Silvercrest SBB 850 C1 - IAN 270356 (Seite 15 von 90) (Holländisch)

646206

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

SBB 850 C1

Ending a programme

When the baking process has been completed,

you will hear ten beeps and the display  indicates

0:00. At the end of the programme, the appliance

automatically changes to a keep-warm mode for

up to 60 minutes.

NOTE

►

This does not apply to programmes 6, 7 and 11.

In this mode, warm air circulates inside the appli-

ance. The keep-warm function can be ended early

by keeping the Start/Stop button  pressed until

a beep is heard.

DANGER! ELECTRIC SHOCK!

►

Before opening the appliance lid 2, discon-

nect the power plug from the socket. The

appliance should always be disconnected

from the power grid when not in use!

Taking out the bread

Always use pot holders or oven gloves when re-

moving the hot baking mould 7. Hold the baking

mould 7 tilted over a grill tray and shake it lightly

until the bread slides out of the baking mould 7.

If the bread does not slip oﬀ the kneading blades 6,

carefully remove the kneading blades 6 using the

supplied kneading blade remover 0.

NOTE

Do not use any metal objects that could cause

scratches on the non-stick coating. Rinse the

baking mould 7 with warm water directly after

removing the bread. This will help prevent the

kneading blades 6 becoming stuck on the drive

shafts.

TIP

If you remove the kneading hooks 6 from the

dough after the last kneading process, the bread

will not be torn open when removing it from the

baking mould 7.

■ Press the Start/Stop button  brieﬂ y to pause

the programme at the very start of the baking

phase or, pull the power plug out of the socket.

Ensure that you replace the power plug within

10 minutes so that the baking process can be

continued.

■ Open the appliance lid 2 and remove the

baking mould 7. With ﬂ oured hands, you can

remove the dough and then pull out the knead-

ing hooks 6.

■ Replace the dough in the back baking mould 7.

Replace the baking mould 7 and close the

appliance lid 2.

■ Put the power plug into the socket if necessary.

The baking program continues from where it

was stopped.

Allow the bread to cool for 15–30 minutes before

eating it.

Before cutting the bread, always check to ensure

that the kneading blades 6 have been removed

from it.

Error messages

■ If the display  shows "HHH" after the pro-

gramme has been started, it indicates that the

temperature in the bread maker is still too high.

Stop the programme and remove the power

plug. Open the appliance lid 2 and allow the

machine to cool down for 20 minutes before

reusing it.

■ If a new programme cannot be started directly

after the bread maker has completed a baking

process, it means the appliance is still too hot.

In this case, the display panel reverts to the

default setting (programme 1). Open the ap-

pliance lid 2 and allow the machine to cool

down for 20 minutes before reusing it.

NOTE

► Do not attempt to reuse the appliance until it

has cooled itself down. This functions only in

programme 12.

IB_270356_SBB850C1_LB3.indb 12 24.08.15 17:50

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest SBB 850 C1 - IAN 270356 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Silvercrest SBB 850 C1 - IAN 270356

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info