Bedienungsanleitung Silvercrest SDB 2400 A1 - IAN 270676 (Seite 12 von 51) (Deutsch, Englisch, Holländisch, Français)

645208

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

SDB 2400 A1

Automatic switch-oﬀ

This steam iron is ﬁtted with an automatic switch-oﬀ

system. This stops the steam iron from heating up.

When the steam iron is resting on its sole and is not

moved for approx. 30 seconds, 6 warning beeps

will sound, “PAUSE” appears and the display 

lights up red. After a few seconds, the display illumi-

nation  switches oﬀ. The steam iron will stop

heating up.

To deactivate the automatic switch-oﬀ, lift up the

steam iron and move it gently from side to side.

The display  lights up blue, the previously set

temperature level is shown and the steam iron

heats up again.

When the steam iron is resting on its base  and is

not moved for approx. 8 minutes, 6 warning beeps

will sound, “PAUSE” appears and the display 

lights up red. After a few seconds, the illumination of

the display  switches oﬀ. The steam iron will stop

heating up.

To deactivate the automatic switch-oﬀ, lift up the

steam iron and move it gently from side to side.

The display  lights up blue, the previously set

temperature level is shown and the steam iron

heats up again.

NOTE

The automatic switch-oﬀ is not intended as a

substitute for removing the plug from the mains

power!

It is merely designed to prevent the appliance

from overheating and helps to avoid unneces-

sary power consumption.

It does not, however, in itself provide ﬁre protec-

tion, for instance, if you place and leave the hot

steam iron on ﬂammable material.

Cleaning

Self-cleaning function

1) Fill the water tank to the marking MAX.

2) Insert the plug into the mains power socket.

3) To switch on the iron and set the temperature,

press the

TEMP button - repeatedly until

9/MAX appears on the display .

4) Set the steam regulator  to maximum steam

power.

5) Allow the steam iron to heat up to the set

temperature.

6) Hold the steam iron horizontally over a catch-

ment receptacle.

7) Press and hold down the self-clean button .

Steam and boiling water ﬂows from the steam exit

holes in the sole of the iron. Impurities that may be

present are washed out.

8) Release the self-clean button  as soon as all

of the water has run out.

9) Iron over a towel or old piece of material a few

times to dry the sole of the iron thoroughly.

10) Press the

TEMP button  repeatedly until

you hear a signal, the display lights up red

and indicates OFF.

11) Remove the plug from the mains power socket.

12) Allow the steam iron to cool down before

placing it in storage.

Housing

WARNING –

RISK OF ELECTRIC SHOCK!

► Always remove the plug from the mains power

socket before cleaning the appliance.

► Never open the appliance housing! Otherwise

there is a risk of a fatal electric shock.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest SDB 2400 A1 - IAN 270676 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Silvercrest SDB 2400 A1 - IAN 270676

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info