Bedienungsanleitung Silvercrest SDBE 2600 A1 - IAN 290451 (Seite 23 von 88) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

679074

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

SDBE 2600 A1

■ 20

│

■ Move the temperature control  to the "MIN"

position.

■ Stand the steam iron only on the base .

After use

■ Remove the power plug from the mains power

socket.

■ Empty the water tank and clean the sole of the

iron .

■ Place the cooled-down steam iron on the base .

Automatic descaling function

(ANTICALC)

There is a descaling cartridge in the water tank that

helps reduce the build-up of limescale.

This descaling cartridge is a permanent ﬁxture in

the water tank and cannot be replaced.

Drip-Stop function

With conventional steam irons, water can drip from

the sole of the iron  at low temperatures.

This iron, however, possesses a new feature: the

DRIP-STOP function ( ). At low tem-

peratures the iron automatically switches oﬀ the

steam-blast function.

Then set a suitable temperature with the tempera-

ture control . As soon as this is reached, steam

production is resumed.

Automatic switch-oﬀ

This steam iron is ﬁtted with an automatic switch-oﬀ

system. This stops the iron from heating up.

If the iron is resting on its sole  and is not moved

for about 30 seconds, there will be a warning beep

and the control lamp for the automatic switch-oﬀ 

ﬂashes. The iron will stop heating up. To deactivate

the automatic switch-oﬀ, lift up the iron and move

it gently from side to side. The control lamp for the

automatic switch-oﬀ  goes out and the iron will

heat up again.

If the iron is resting on its base  and is not moved

for about 8 seconds, there will be a warning beep

and the control lamp for the automatic switch-oﬀ 

ﬂashes. The iron will stop heating up. To deactivate

the automatic switch-oﬀ, lift up the iron and move

it gently from side to side. The control lamp for the

automatic switch-oﬀ  goes out and the iron will

heat up again.

NOTE

The automatic switch-oﬀ is not intended as a

substitute for removing the plug from the mains

power! This is merely intended to reduce the ﬁre

hazard if you forget to switch of the iron!

Cleaning

Self-cleaning function

■ Fill the water tank to the "MAX" marking.

■ Insert the plug into the mains power socket.

■ Move the temperature control  to the "MAX"

position.

■ Set the steam control  to maximum steam

power.

■ Allow the steam iron to heat up until the heat

control lamp  goes out and then lights up

again.

■ Hold the steam iron horizontally over a suitable

container.

■ Press and hold down the self-clean button -.

Move the steam iron back and forth a little.

Steam and boiling water will ﬂow from the

steam exit holes in the sole of the iron . Any

impurities that may be present are ﬂushed out.

■ Release the self-clean button - as soon as all

of the water has ﬂown out of the water tank.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest SDBE 2600 A1 - IAN 290451 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info